My Orders
UDT165SIV0II General Electric Dishwasher - Overview
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$16.05
In Stock
4.1 Amp Control Board Fuse
Part #WD21X25696
$31.66
In Stock
$17.22
In Stock
Wheel Stud Assembly Lower Rack
Part #WD12X24712
$82.64
In Stock
Piranha Clamp Kit
Part #WD35X10382
$16.00
On Order
RACK SLIDE END CAP
Part #WD12X24354
$69.25
In Stock
DRAIN PUMP ASM
Part #WD19X24651
This dishwasher drain pump assembly is designed to remove water from the tub during the drain phase of the wash cycle, ensuring efficient water expulsion and proper cycle completion. It is commonly used in select dishwashers and serves as a direct replacement for the original part. A failing drain pump may result in standing water, slow o...Read morer incomplete draining, or unusual noises during operation. Replacing the pump can restore proper drainage and improve overall performance. Before installation, always disconnect the appliance from both power and water sources. Compatibility should be confirmed by checking your dishwasher’s model number to ensure a proper fit.
Read less
$28.72
In Stock
MID SPRAY ARM CONDUIT ASSEMBLY
Part #WD22X25158
This mid-level spray arm conduit assembly directs water to the upper spray arm to improve cleaning coverage, especially in hard-to-reach areas. It’s typically replaced when the dishwasher leaves dishes dirty, leaks, runs noisily, or when the spray arms stop spinning properly. Made from durable plastic, it restores proper water flow and he...Read morelps ensure consistently clean results. Installation usually involves removing the lower rack, releasing the old conduit from its mounting tabs, aligning the new assembly with the feed tube and spray arm, and snapping it securely into place.
Read less
$30.40
In Stock
FINE FILTER
Part #WD12X24656
This fine filter traps small particles before they enter critical components. Proper filtration supports efficient operation and protects internal systems. Replacing a clogged filter restores performance and reliability.
$80.38
In Stock
UI CONTROL ASM
Part #WD21X28718
$37.18
In Stock
Mid Spray Arm & Gasket Assembly
Part #WD22X24742
$37.20
In Stock
Wheel Stud Assembly Upper Rack
Part #WD12X24713
This wheel stud assembly supports smooth movement and alignment of the upper rack. It is commonly replaced when racks bind, derail, or fail to slide properly. Appliance compatibility should be confirmed before installation.
$60.27
In Stock
Common Symptoms of the UDT165SIV0II
How this model fails, and the parts that fix it.
Will Not Start
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Watch our pros, then fix it yourself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
While the dishwasher door was fully open, someone accidentally turned and tripped over it with much of their weight. Now the door won't fully close.
3 of 7 people
found this instruction helpful.
*UNPLUG THE DISHWASHER
*remove 2 mounting screws attatching dishwasher to underside of countertop.
*with the dishwasher door closed, remove left and right side hinge cables off pulley and hinge.
*fully open door and remove all perimeter screws except for 2 screws holding the latch assembly.
*carefully separate outer ... Read more door shell from door body.
*disconnect electrical clip from inside top of outer shell. Carefully set outer shell aside.
*each hinge has 2 Torx head screws and 2 Phillips head screws, remove these. You can now slide the door body out and away from the hinges and dishwasher.
*these hinges were slightly bent so I had to use a ball peen hammer to tap them off the post.
To reassemble, reverse these instructions.
*remove 2 mounting screws attatching dishwasher to underside of countertop.
*with the dishwasher door closed, remove left and right side hinge cables off pulley and hinge.
*fully open door and remove all perimeter screws except for 2 screws holding the latch assembly.
*carefully separate outer ... Read more door shell from door body.
*disconnect electrical clip from inside top of outer shell. Carefully set outer shell aside.
*each hinge has 2 Torx head screws and 2 Phillips head screws, remove these. You can now slide the door body out and away from the hinges and dishwasher.
*these hinges were slightly bent so I had to use a ball peen hammer to tap them off the post.
To reassemble, reverse these instructions.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!