EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

UCC15NPRDII General Electric Ice Maker - Overview

Diagrams for UCC15NPRDII

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator Water Filter – Part Number: GSWF
$69.91
In Stock
Refrigerator Water Filter
★★★★★
★★★★★
(14)
Part #GSWF
This OEM filter is sold individually. Change your filter every 6 months for the best results. This filter is found in top-freezer and bottom-freezer refrigerators located in the back upper right corner. It measures 4.75-Inches deep 9.5-Inches high and 5.25-Inches wide. It is certified to reduce particles chlorine-resistant cysts lead and five other impurities. The pressure requirement is 40-120 PSI (if yours exceeds this you?ll need to install a pressure-timing valve) and the operating temperature needs to be 33-100 degrees Fahrenheit. It filters down to 0.5-1 microns. The installation is simple and does not require any tools or mess. To remove the old cartridge turn it to the left and pull down carefully. Some water might drip so keep a cloth handy. To install the new filter place it into the cartridge holder and turn to the right until it will no longer turn. If you have a top-freezer model it should be situated vertically and if it is a bottom-freezer model it should be placed horizontally. Be careful not to over-tighten. If your model has a replacement indicator light reset it by pushing and holding it down for three seconds. If your model has a dispenser run water through it for approximately 3 minutes to clear the system. Please note that this filter will not work in Kenmore brand models.
GSWF BYPASS – Part Number: WR17X22073
$27.42
Special Order
GSWF BYPASS
★★★★★
★★★★★
(1)
Part #WR17X22073
Water can still flow to the refrigerator dispenser and ice maker when the filter is removed by using this OEM bypass plug in the water filter head. Check your refrigerator model to confirm compatibility. Unplug the ice maker before installation. Side panel removal may be required.
Refrigerator Water Filter Head and Tubing – Part Number: WR17X12301
$67.82
In Stock
Refrigerator Water Filter Head and Tubing
Part #WR17X12301
The water filter head and tubing holds the water filter and comes with the water lines.
WATER VALVE – Part Number: WR57X38936
$59.19
In Stock
WATER VALVE
Part #WR57X38936
A two-port solenoid valve regulates water flow to the ice maker in compatible refrigeration equipment. Check your appliance model before ordering this OEM part.
DRAIN VALVE – Part Number: WR87X38941
$61.55
In Stock
DRAIN VALVE
Part #WR87X38941
This 120 VAC solenoid valve controls water drainage from a refrigerator ice maker. It is an OEM replacement. Confirm fit using your appliance model number before ordering.
BOTTOM HINGE – Part Number: WR13X38604
$113.45
Special Order
BOTTOM HINGE
Part #WR13X38604
PRESSURE SENSOR & HOSE – Part Number: WR01X46445
$49.50
On Order
PRESSURE SENSOR & HOSE
Part #WR01X46445
Pressure changes during ice maker operation are detected by this sensor and hose assembly. It is an OEM part listed for select ice makers. Confirm compatibility with your appliance model number before ordering.
WIFI & BLUETOOTH BOARD – Part Number: WH22X36577
$59.14
In Stock
"UNION CPLG. 1/4"" " – Part Number: WR97X10031
$38.96
In Stock
"UNION CPLG. 1/4"" "
Part #WR97X10031
This tubing coupling joins two 6 mm refrigerant tubes in the appliance sealed cooling system. It forms a mechanical connection without soldering or brazing when assembled with the matching tools and specified sealing compound. Both tube ends must match the fitting size for the joint to seal correctly. Follow the connection instructions for preparing the tubing and pressing the assembly into place. Confirm the required metric diameter before selecting the coupling, since 6 mm and 1/4 inch are not exact equivalents and may require different fittings. This is an OEM part sourced directly from the manufacturer.
"CPLG. 1/4""-3/16"" " – Part Number: WR97X10034
$41.07
In Stock
"CPLG. 1/4""-3/16"" "
Part #WR97X10034
This reducing coupling joins a 6 mm refrigerant tube to a 5 mm tube in the refrigerator sealed cooling system. It forms a mechanical connection without welding or soldering when used with the matching assembly tools and specified sealing compound. Both tube diameters must match the fitting for the joint to seal correctly. Follow the connection instructions for preparing the tube ends and assembling the coupling. Confirm the required metric sizes before selecting the fitting, since nearby inch sizes are not exact equivalents and may require a different connector. This is an OEM part sourced directly from the manufacturer.
"CPLG. 5/16""-1/4"" " – Part Number: WR97X10036
$45.29
In Stock
"CPLG. 5/16""-1/4"" "
Part #WR97X10036
This reducing coupling joins an 8 mm refrigerant tube to a 6 mm tube in the refrigerator or freezer sealed cooling system. It provides a mechanical connection between the two tube sizes without soldering or brazing. Assembly requires the matching connection tools and specified sealing compound. Follow the instructions for preparing the tube ends and pressing the fitting into place. Confirm both tube diameters before ordering so each opening matches the intended line, since similar looking connectors can have different sizes and repair applications. This is an OEM part sourced directly from the manufacturer.
".295"" - 1/4"" BRASS RE – Part Number: WR97X10081
$50.56
Special Order
".295"" - 1/4"" BRASS RE
Part #WR97X10081
This brass reducing connector joins a 0.295 inch refrigerant tube to a 1/4 inch tube in the appliance sealed cooling system. It forms a mechanical joint between the two different tube sizes when assembled with the matching connection tools and specified sealing compound. Both tube ends must match the fitting openings for the joint to seal correctly. Follow the connection instructions for preparing the tubing and assembling the fitting. Confirm both diameters before ordering, since similar looking connectors may have different openings and may not fit the same refrigerant lines. This is an OEM part sourced directly from the manufacturer.

Common Symptoms of the UCC15NPRDII

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
I have weak thumbs
53 of 117 people found this instruction helpful.
  • Lois from Green Valley, AZ
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Required pliers to remove old - be careful. New went in very easily per instructions.
Was this helpful?
Thank you for voting!
Water filter light came on in my refrigerator.
5 of 5 people found this instruction helpful.
  • Barbara from KILMARNOCK, VA
  • Very Easy
  • Less than 15 mins
  • Pliers
Opened the water filter sleeve on the inside of my refrigerator. Removed the old water filter cartridge. It was a little stuck so I used a pliers to turn the cartridge counterclockwise. The old cartridge slipped out. I inserted the new cartridge and turned it in clockwise until it "clicked." Closed the water filter sleeve. Reset the butto n on my fridge. All set to go.
Was this helpful?
Thank you for voting!
No water from dispenser, just a trickle
4 of 5 people found this instruction helpful.
  • Nancy from PARRISH, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Wrench (Adjustable)
Troubleshooting was the most difficult job, but Parts Select helped with good info and videos. The water filter pushes down on a small plunger that allows the water to flow. If the water filter is bad or clogged up and needs replacement this plunger will not allow the water flow. I tried using the water filter bypass plug but this did n ot solve the problem either. The plunger was defective or worn out. I ordered the filter & tube assembly from parts select, and followed the simple instructions to change it out. Turn off the water supply first and put some towels down because they’ll be a little spillage out of the tubes. Unscrew both of the tubes with a crescent wrench. Remove the two screws on the filter assembly inside the refrigerator, and pull it forward to take it out -the tubes will follow. Insert the new assembly, tubes first thru the hole inside the back of the refrigerator. Reconnect the tubes and remount the filter assembly inside. Stuff putty back inside the hole with the tubes and reattach the metal cover. This is an easy repair. I am an old lady, so the hardest part was pulling the refrigerator out to get behind it!
Was this helpful?
Thank you for voting!