Models
>
UAN6506-87D
UAN6506-87D Frigidaire Washer - Overview
Sections of the UAN6506-87D
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
V-Style Belt
PartSelect #: PS459613
Manufacturer #: 5303280326
This v-style belt or drive belt is designed for use in your washing machine. This part connects the drive motor to the drive system in the washer, which spins the basket. If you notice a burning smell...
$37.34
In Stock
SPACER
PartSelect #: PS474201
Manufacturer #: 5308015493
This spacer is used in washers or a washer and dryer combo unit. Spacers are used to create space between cotter pins, lock nuts, hitch pins or to fill the space between machinery parts in a washer. T...
No Longer Available
Snubber Ring
PartSelect #: PS473378
Manufacturer #: 5308002385
The snubber ring on your washing machine mounts at the base, under the support. If you notice that your washing machine is vibrating, shaking, or moving during the wash cycle, you may need to replace ...
No Longer Available
TRUNNION
PartSelect #: PS418105
Manufacturer #: 131545101
This part helps with the spinning and agitating cycles.
$111.47
In Stock
Transmission Assembly
PartSelect #: PS1524604
Manufacturer #: 134736400
This part aids in the spinning and agitating cycles. The length of the shaft on this part is 13". The seal/gaskets are NOT included.
$737.69
In Stock
Motor and Drain Pump Assembly
PartSelect #: PS416713
Manufacturer #: 131027600
Motor is 120 volts.
No Longer Available
Rotary Knob - Stainless Steel
PartSelect #: PS473639
Manufacturer #: 5308008462
$32.39
Special Order
Questions And Answers for UAN6506-87D
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the UAN6506-87D
[Viewing 2 of 2]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
belt worn causing machine to make all kinds of noise
pull up on top ,take two screws loose on front panel(pull off) vaccum old debri out,pull tension pulley back pull old belt off,holding tension pulley put new belt on .put front panel back on and snap top back down to secure.
working perfectly nice and quite !!!
working perfectly nice and quite !!!
Parts Used:
-
Kenneth from Baltimore, MD
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
19 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drive belt replacement
removed rear panel, tilted machine forward, removed four bolts holding the pump and loosened the connection to the motor shaft,(several times dropped socket and without magnet to retrieve tools would have been much more difficult),removed two hoses, dropped pump assembly, replaced belt, and reversed the process to re-assemble. Easy to fin
... Read more
d part and will definitely use your parts finder again. Lots less expensive than repair service or replacement
Read less
Parts Used:
-
Scott from Cumming, GA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Worn out belt replacement
First unplug power cord and removed water hoses, then removed rear panel of machine. Shop-vac old debries out of machine Remove small spring holding belt tensioner pulley assembly. Remove hex key from motor shaft that connects to the pump. Use pliers to spin clamps out of way so you can then remove the (4) four bolts that hold pump to bot
... Read more
tom of the motor, no need to remove other pump bolts. I used a straight screwdriver to pry the pump loose from the motor shaft to slip the old belt out of the machine. Put new belt on and reversed process for reassembly. :Note: Shop vac up water that leaks out of pump when you remove the 4 bolts, also wipe down pump so you can check for leaks after tightening pump back onto motor.
Read less
Parts Used:
-
DAVID from WAPAKONETA, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!