This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer, your washer does no...
$24.32
In Stock
Order within the next 9 hrs and your part ships today!
The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve i...
$45.53
In Stock
Order within the next 9 hrs and your part ships today!
This is a screw in leveling leg for your washing machine. It supports the appliance by screwing in place to create a stable and flat surface. Take note that you are able to adjust the height of your a...
$25.94
In Stock
Order within the next 9 hrs and your part ships today!
If you have a leaky washer, then your tub seal may be the culprit. The tub seal assembly may also be known as the washer tub seal, and is a part for your washer. The function of this piece is to make ...
$70.62
In Stock
Order within the next 9 hrs and your part ships today!
The idler pulley on your washing machine allows the drive belt to operate smoothly. If your washer is not spinning or agitating, makes too much noise, or you notice a burning smell when it is operatin...
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$24.72
In Stock
Order within the next 9 hrs and your part ships today!
The agitator drive block rotates the agitator assembly in your washer. If the drive block breaks down due to wear and tear the agitator will stop working. If you notice that your washer is making loud...
$61.83
In Stock
Order within the next 9 hrs and your part ships today!
The spin bearing, used for your washer, is located at the bottom of the outer tub near the transmission. The spin bearing carries the transmission shaft in the drive system, therefore ensuring the sha...
$78.32
In Stock
Order within the next 9 hrs and your part ships today!
The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for this replacement are ...
$14.98
In Stock
Order within the next 9 hrs and your part ships today!
Questions And Answers for TWX645RBW2
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run belt on,release tension on idler arm.replace front panel and lower top.WALAAH!!!! you are done.
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and removed the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.
The Lid Lock Assembly came super fast! The install would have been flawless, but the "pre-drilled" holes on the new Lid Lock Assembly were way to small. We found that out after we had reconnected the wires and gotten it into place. Aside from that small set back, the install went great! This repair is definitey not one that you would need to pay a repair person to do!
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
