TW0350 Makita Impact Driver - Overview

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

This replacement clip is an authentic OEM component which is made for Makita impact wrenches. The part is secured in the anvil and it helps to apply tension on the socket to secure it. Over time it may wear out and lose tension eventually requiring a replacement. If a socket does not stay put on the anvil, a faulty or a damaged clip may b...Read moree the cause. Make sure to refer to the appropriate diagrams of your model for the exact location and the correct installation of this clip. One durable metal item is included. You will need pliers to remove the old one and secure the new one in the anvil.

This #191938-1 (CB-408) Makita carbon brush set contains two individual carbon brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes are often the cause...Read more of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This authentic Makita replacement part is designed for use with impact wrenches. This pin fits in the anvil and it helps to hold sockets in place. This part is made out of metal and it is sold individually. To complete this repair you would need a screwdriver and pliers.

This cord protector is an OEM part designed for a variety of Makita power tools. It is attached where the power cord meets the tool. This part protects the cord from damage due to pulling, bending, or other strain. This rubber cord protector is sold individually. It does not include a replacement cord.

This genuine manufacturer-sourced part is specially designed for Makita power tools. It is an important component which provides a tight seal between connected components. Unfortunately, over time it will wear out and it may begin to crack eventually requiring a replacement. To ensure the correct repair procedure, refer to the appropriate...Read more diagrams for your model. Note, this high-quality insulation washer is made of durable material and is sold as an individual item. A screwdriver will be needed to take apart and reassemble the tool when performing this repair.

This is an authentic OEM sourced part which is specially made for use with Makita power tools. It is an identical replacement for a missing or a faulty steel ball that was installed on a new unit. This is a standard hardware which may have multiple applications, please make sure to check the appropriate diagrams of your model for the corr...Read moreect location and application of this hardware. Keep in mind this high-quality component is made of durable metal and is sold individually.

This is a Ball Bearing that is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings minimize friction between 2 parts in your tool that would otherwise spin and rub against each other. The balls or rollers take the load and spin, distributing the weight evenly while the minimal co...Read morentact area of the balls reduce friction. This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

Included in Part Number 539168-0