Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TVF15FREW02

TVF15FREW02 Whirlpool Freezer - Overview

Get Parts and Repair Help for TVF15FREW02

If you know the freezer repair part you need, you can browse the list of all parts on the TVF15FREW02, or you can search by name or part description. You can also find your part by where it is located on the TVF15FREW02 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your freezer. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the TVF15FREW02

[Viewing 4 of 4]

Manuals & Care Guides for TVF15FREW02

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.96

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this sc...

$2.96

Screw

Sold individually.

$6.20

Touch-Up Paint - White

This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, ...

$11.38

Spray Paint - 12 oz. - White

Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a protective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.

$61.22

Compressor Relay and Overload Kit

The compressor relay and overload kit is an assembly for your refrigerator. The function of the overload is to protect the compressor from overheating by being mounted to the side ...

$4.88

Screw

Sold individually.

$127.17

Door Gasket

The door gasket is used on vertical freezers. Screws are no longer included with this product. The gasket creates a tight closure around the opening of the door to ensure that outs...

$4.88

Screw

Sold individually.

$5.69

Freezer Door Key

This metal freezer door key has a cross shape and is approximately 2 inches long. If your freezer door will not stay shut, you can use the key as a quick fix to keep it closed. If ...

$46.71

Compressor Start Relay

Overload is sold separately. The start relay briefly boosts the compressor, and then shuts off as soon as the motor gets up to speed.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Scratches in Surface

  • Customer: Michelle from Richardson, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 24 of 33 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great. read more

gasket had harden. frost was building up quickly

  • Customer: LESLIE from TAPPAHANNOCK, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 21 of 25 people found this instruction helpful
the gasket peels back to reveal the approx 20 screwsholding gasket and door shelves. removed these. removed old gasket from door panel. new gasket needs to be stretched to get on door panel. align screw holes in door panel with screw holes in gasket. attached back to freezer door. this gasket did not seal securely when closing door. this gasket was ins... read more

Refrigerator stop working

  • Customer: SAL from UPLAND, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 21 of 30 people found this instruction helpful
First I removed the relay and over load and exam. Saw that the relay was burnt. Before I order the part I check to see if the compressor was still working by jumping the common start and run terminals.It did. I also checked the start capacitor with a capacitor tester it was good. I than order the part which came the very next day.Installed the part read more