TPS-2501 Tanaka Pole Saw - Overview

This individually sold grommet is a genuine OEM part and is used for a variety of different small engine/outdoor lawn equipment. The return fuel line from the carburetor is installed through this grommet, which creates a seal to prevent future leaks and ignition issues. Over time and through exposure to fuel, the grommet can wear down, le...Read moreading to cracks, tears, and missing pieces. If you notice fuel is leaking during operation, or are having issues with starting the engine, this grommet may be the cause. Depending on your model, installing the return line in the grommet and then installing both together in the fuel tank may be easiest, rather than installing them separately.

The fuel pipe/fuel line assembly is a genuine OEM parts kit used in gas-powered outdoor equipment with dimensions of 5mm x 160mm. It includes a pipe or line, which carries fuel from the tank to the carburetor, and a rubber grommet which holds the fuel line in place. The grommet also has a flange that prevents it from being pulled into the...Read more body of your equipment. Over time the grommet may wear down and the fuel line can become brittle and crack causing fuel leakages and difficulty starting or running your equipment. Therefore, it is important to routinely inspect this assembly and replace it when it shows signs of wear. Before your repair, drain the fuel for your safety and to prevent contaminating the fuel tank. To install a new fuel pipe assembly, simply pull off the old grommet and detach the fuel line. Carefully insert your new fuel line into the new grommet and connect the line to the carburetor and the fuel filter inside the fuel tank on your equipment.

This oil tank cover set is sourced from the original manufacturer for use in poles saws. It includes one plastic cover, four collars, four Phillips head screws, four metal washers, and one gasket to seal the area between the plastic cover and the tank. The set can be found at the rear end of the pole saw where it is responsible for protec...Read moreting the oil tank by preventing dirt and debris from entering, and contaminating the oil. Over time the cover and gasket can wear down, crack, or become loose, and unable to protect the tank. This will cause oil leakages, contamination, low cutting power, and eventually total equipment failure. Remove the faulty cover and gasket from the oil tank and clean the surrounding area. Install the new gasket on to the oil tank opening and place the new cover on top of it. Position the four collars into the holes on the cover and then secure the cover to the tank using the screws and washers to complete your repair.

Also known as a priming bulb, this OEM replacement part is an individually sold rubber primer bulb. Since it is made of rubber, it will eventually lose its elasticity and crack or break,and need replacing. It is designed for use with a variety of different small engine equipment and is also known as a purge bulb. Pressing this primer bulb...Read more forces fuel through the fuel line and into the carburetor from the fuel tank. Once the carburetor is has a sufficient level of fuel, any excess fuel will be forced back into the fuel tank through the return line attached to the carburetor. If your primer bulb has a darker appearance or has lost its elasticity and does not return to its original shape, it means the rubber will likely soon crack, which will lead to fuel leaking into the engine and ignition system. To replace your primer bulb, simply remove the outside cover and primer bulb cover and replace the bulb within its housing.

This fuel line/pipe is a genuine manufacturer approved replacement part. It is commonly used with Tanaka gas powered engines. The fuel line is what delivers the fuel from the fuel tank into the carburetor. Over time it will deteriorate, become brittle and may crack. This item is made out of flexible plastic material and it is sold individually.

This is a genuine OEM replacement part, it is sold individually. The Fuel Filter is inside of the fuel tank. Its purpose is to filter out dirt and other debris from contaminating the carburetor. It will at sometime become clogged and restrict the fuel getting to the carburetor,and will have to be replaced. We do have an article and vide...Read moreo on How to Replace the Fuel Filters in Your Outdoor Power Equipment.. You can see this by going to the front page of our site and clicking on Repair Center.

This is an authentic OEM sourced replacement part commonly utilized on Hitachi and Tanaka handheld lawn and garden equipment. The purpose of a spark plug is to deliver electric current to an internal combustion engine. Symptoms of a failing or faulty spark plug include difficulty starting the saw or a complete failure to start. Please not...Read moree, this item is sold individually. You would need a spark plug wrench or a socket wrench to complete this repair.

This item has been OEM sourced to ensure a high level of quality. The clip is intended to be used with trimmers and blowers from Hitachi and Tanaka. The metal clip is part of the fuel system. The clip is used to fasten the fuel filter and the fuel line assembly. This part is priced as an individual replacement part.

This is a replacement part sourced directly from the manufacturer for Tanaka grass trimmers. The gas cap covers the opening of the grass trimmer tank and prevents gas from spilling out. To install or replace the gas cap requires no tools, simply twist the cap into place on the tank. This part is made of plastic and is sold individually.