TMO-33942A ((130-670G088)(1990)) MTD Lawn Tractor - Overview

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

Sourced directly from the original manufacturer, this Bell Washer is made of gold-colored metal and is sold individually, not as part of a kit or assembly. It is used to provide spacing between various part assemblies along a shaft. If you hear a strange noise coming from the shaft area, or you notice the Washer is visibly worn or damag...Read moreed, it will need to be replaced. Refer to your owners manual to determine the exact location of this part. Customers rate the difficulty of this repair as Medium.

When the brakes are applied, this brake puck presses against the brake disc in your lawn equipment to help slow down or stop it. The brake puck is in the brake assembly, which might be located near the transmission or the wheels of your machine. If you notice that the machine takes longer to stop or that there is a loud scraping or grindi...Read moreng noise when you push down on the brake, your brake puck may have worn out. If it is not replaced, you risk losing braking power, which leads to equipment damage or accidents. Before any repairs, make sure that your machine is turned off and that the spark plug is disconnected. To dissemble the brake assembly and access the brake puck, use pliers or a wrench to remove any bolts or clips holding it in place. With a screwdriver, pry the brake puck out of your machine. Since this genuine OEM part is sold individually, determine the number of pucks your machine needs by consulting your user manual.

This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual

This ball joint connects moving parts in the steering or control linkage of select lawn tractors and snow blowers. It has 3/8-24 male and female right-hand threads. The male threaded end is shorter than a standard joint. Use the complete equipment model and serial number to guarantee the proper fit. Replace the joint if it is loose, bent,...Read more rusted, or hard to move. Before removal, measure the linkage or count the exposed threads so the new joint can be installed in the same position.

The Push Cap is a black plastic cap which secures to the end of a shaft to prevent injury. It can be installed with a hammer and is rated as "Easy" to install. If the part appears damaged or worn down in a way that could cause injury, it should be replaced. Refer to your make, model and diagrams to check if this is the right part for you.

The Hex Flange bearing, .630 inches I.D. is an OEM part. Black in color and made of metal, it is sold individually. It is installed using a wrench or socket and its installation has been rated as Easy by consumers. This part attaches on the worm gear shaft in the cute, and is used to secure the worm gear on the shaft. If broken, you wil...Read morel no longer to be able to control the chute (or you may only have partial control). This breakage can occur due to fatigue over time, and means the part must be replaced. Refer to your owners manual or model number to ensure you are purchasing the correct part.

This authentic OEM hi-pro key, also called a woodruff key or key stock, is a metal component found in your lawn equipment that connects rotating parts. It is 3/16 inch wide and 5/8 inch long. It fits into a specially-shaped slot on a shaft and prevents the parts from moving or slipping out of position while your machine is running. To fin...Read mored and replace a hi-pro key on your machine, check your user guide for instructions. When removing the hi-pro key, insert a flathead screwdriver or needle-nose pliers into its groove and pry it out of its slot. Please bear in mind that this hi-pro key is sold individually.

This is an authentic MTD replacement part that has been sourced from the original manufacturer to be used with lawnmowers. The metal blade adapter is used to provide spacing between the blade and the blade spindle assembly. This item is sold as an individual replacement part.

This Flat Washer is made of durable gold-colored metal and is an authentic OEM part. It is used to spread the load under a bolt or nut and is sold individually. This part will need to be replaced if you notice any signs of cupping, corrosion, or other damage. Customers rate this repair as Easy.

It is an authentic OEM part which is made for use with lawn and garden equipment. This is the special self-tap screw that helps to secure components together. If the hardware is missing or is damaged, this will provide an identical replacement for the original hardware that was installed on a new unit. This high-quality screw is made of d...Read moreurable metal and is sold as an individual item. Refer to the owners manual and the appropriate diagrams for your model to ensure the proper replacement procedure. A wrench will be needed to secure and remove this hex washer head self-tap screw.

This special jam nut is sourced directly from the original equipment manufacturer for use with MTD and Ryobi lawn and garden equipment. It is a standard hardware which has multiple applications depending on your tool, please refer to appropriate diagrams for correct location and use of this part. It is made of high-quality metal and it is sold individually.