TGFS63DSE Tappan Range - Instructions

Screw the handle, that it...

Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly

Very easy just had to pull the wire up that holds it secure.

After looking over the installation instructions I was confident that I could perform this on my own, However, changing the burner orifices was a bit tricky. Getting the original ones out worked well, they stayed in the nut driver when it was lifted. One of the new ones fell out when inserting it. Thankfully it fell all the way down and I could retrieve it. A small piece of tape was needed to keep it in the driver. The rest of the install went per instructions.

Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy just the spark module for the burner.

On the front left burner would not ignite, after the installation of the new one, same problem, new one didn't fix.. I guess it's something with the electric igniter

I researched the actual problem and found the correct part to order. My husband researched repair videos and saved them until our part arrived. On repair day he pulled the oven away from the wall, turned off the gas to the oven at the shutoff, and unplugged the electric cord. He removed the oven door, baking racks, oven floor, shield under the oven floor, and storage drawer. It was a little awkward for him to get at the igniter location in the center of the oven. Once he got the old igniter unplugged and the new one in place, he followed the video instructions to plug the electric cord in again to test the new part -- while everything else was still dismantled. The new igniter fired on in just a few seconds and glowed red, just as expected. Successful test! Then he reassembled all the parts, needing a third hand to hold the igniter assembly in place so he could put in the screws. He took his time, and thinks it took him about an hour. I took a golden opportunity to soak the racks and oven floor in Oxi-Clean for an hour, then scrubbed with steel wool (not the unpainted shields!), and eventually the oven front, and inside walls. Once we had everything in place we turned on the oven, listened gratefully to the speedy ignition, and let it run for about 25 minutes. This 20 year old oven looks and works like a new model again -- and it's mostly clean. All in all, this was a fairly easy repair. We've never done this before, and tread carefully through it. We didn't want to mess with gas. Hooray and congratulations! I'm rather proud of him :)

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

Had to pull back off due plug in for bake Ignitor is on bottom right Conner , mfg ill design , part was is to install after that. Parts select is great to deal with first part showed up damage due to shipping , parts select sent another with better packaging , works great have used them in the past for Ref ice maker parts . Due it yourself save money

Very easy to order,part was delivered promptly and installation was easy.I unscrewed a few screws and lifted the bottom panel out and put the new one in.

Very simple. I removed the oven racks, loosened the two screws that held the old panel in place, lifted out the old panel and replaced it with the new one, then tightened the screws to hold the new panel in place. It took no more than 10 minutes.

Removed both oven racks the removed two screws in back. Lifted rear of panel until front lip of panel was free. Installed new panel in reverse order. I was recycled the old steel panel at our local recycling station.

Slide Range away from wall, unplug Range, remove rear cover (4) screws, removed burner assembly (5) screws, unplugged Igniter connector, loosen Igniter bracket, remove Igniter (2) screws. Reverse process to install new Igniter. I also wore latex gloves to prevent touching graphite portion of Igniter. Tested Broiler for operation, slid Range back into position. All good.

moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.

I was getting an error code every time I turned my oven on. After a Google search I discovered it was a faulty oven temperature sensor. This website is awesome because it has a video showing how to install