TGFS63CQB Tappan Range - Instructions

First I turned off the circuit breaker to the oven. Then, I removed the base of the oven (the oven floor) by easily removing two screws. I also removed the flame guard by removing a screw. That easily exposed the old oven igniter. I removed the two small screws that held that in place. The igniter is connected by two wires, which you'll have to snip. Snip those very close to the igniter (leave about an inch of wire on the igniter). Using a wire stripper, remove about 1/2 inch of the outer sheath of the existing wires. On the new igniter, snip the wires leaving about 2 inches still connected to the igniter. Using the wire stippers, remove about 1/2 inch of the outer sheath. Using the plastic wire caps that came with the new igniter, connect the wires from the oven to the corresponding wire on the new igniter. Screw the new igniter back in place. Replace the flame guard and oven floor. Turn on the circuit breaker and start cooking again!

Opened the oven door, removed the racks. Removed the bottom cover, two thumb screws in the rear, bottom, of the oven. This exposed the top plate of the burner, (actually in the top of the broiler section) 1 nut took this cover off. Now, the burner and the igniter are exposed. Two screws removed the igniter, and two wires with ceramic wire nuts. Disconnected these two wires and that was it. Installed the new igniter in reverse procedure as above. Pretty easy. Probably should have turned off the power to the Range first just to be safe.

It went very well. Very quick. Just took out a couple of screws, took out the rest of the broken glass, slipped the new piece in and screwed it all back together. This was the first time I had ever tried to fix any part of a range/oven before, it was very simple...

snapped the new piece of plastic in its place and ta da, its fixed.

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

It was a replace racks not repair. No problem

Took the drawer out, snapped the new glide in place, and replaced the drawer. Installation was simple with no tools required.

Removing the drip pan and the bottom burner cover exposed the igniter, removing two screws retaining the bracket freed the old igniter. Removing the warming drawer allowed access to the control module to unplug the wiring on the ignitor. After making myself a diagram, I unplugged the wires and removed the malfunctioning igniter. Cutting the leads off the old igniter long enough to splice it on below the oven bottom with the enclosed wire nuts and attaching the new igniter (reusing the old insulation to protect the wire) took only minutes and reassembly was straightforward.

New igniter: $60
Repairman fee saved $150
Being able to tell my wife "See,
I told you I could fix it!" PRICELESS

First took apart oven door. then took out broken glass and replaced with new glass.Put everything back together done.

It went easy, I ordered the part from another vendor, received it in 3 days and it only took about 20 minutes to install.
I do not recommend ordering from PartSelect!

I used good old commom sense to disassemble and reassemble the frame, handle, internal glass,and inter panel to reach and repace the cracked glass. I must admit I had two machine screws left over during reassembly, but found a home. It is important to identify where each and every screw belongs. This will cut down your repair time. I thank PartSelect for providing great service and assisting me in my time of need.

Marv Dixon

First removed oven racks then two screws to remove oven door, removed two screw of oven fan cover, ( need to remove fan cover to have clearance to removed bottom cover of oven) removed bottom cover of oven, then removed two screws holding oven igniter and cut wires of old igniter then spliced wire of new igniter to existing wire and reassemble in reverse order.

Disconnected the oven from the wall outlet. Removed the bottom panel of the oven to reach the parts. Reached in the thight spot (not for a big guy)to unscrew the old igniter. Installed the new one. Plug the oven back. Turn the oven on bake at 350. Oveb lighted up in 5 seconds ! Working great since then!!!

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly