TGFS26CSB Tappan Range - Instructions

I searched the item I needed and followed a link to PartSelect.com. I paid a little extra for shipping and literally recieved the part in two days. The part was an absolute perfect fit and my wife and myself have never been happier. Home cooked meals again thanks to the folks at PartSelect.com. It couldn't have been an easier.

removed shelves and base, removed 2 screws that held igniter on, disconnected wires from gas valve removed protective cover in corner {1 screw}
disconnected plug, removed igniter. This igniter was easier to remove from front of stove on this model

Working on an old oven is difficult. Please expect the unexpected. The years of heating and cooling play havoc with oven parts. The screws holding the Flat Style Oven Ignitor become stripped. It took extra time to remove them. I had to go to the hardware store to buy replacement screws. Once I removed the old parts and had replacement ... Read more screws the job was very easy.

First, I unplugged the oven from the wall. I opened the bottom drawer of the oven to see where the igniter was mounted, which was directly under the bottom pan of the oven itself. I opened the main oven door and unscrewed the 2 screws that were holding the pan to the bottom of the oven. Then, I slid the pan back towards the the back of t ... Read more he oven and it popped right out.

There were 2 hex screws that were holding the old igniter on, so I unscrewed them with my socket set. I made sure to pay attention to which wire was the top one and which one was the bottom one coming out the back of the igniter. I pulled off the wire nuts connecting the igniter wires to the wires of the oven. I striped the wires on the new igniter and re-attached them to the proper wires of the oven, using the included replacement ceramic wire nuts. I re-screwed the hex nuts in, mounting the new igniter to its proper place. I put the pan back and screwed the 2 screws back in to hold it in place.

Plugged it back in, turned it on, fired up within 20 seconds. Good as new.

Twisted replacement bulb into place easily. Let there be light!

Slid oven out removed one screw one plug replaced part took 5 minutes.told parts repair the error message and they sent me the correct part in two days will use them again saved me from Repair man wanted 85 dollars just to look at it my cost was 28 for probe and 8 dollars for shipping already helped neighbor with their stove they needed n ... Read more ew ignighter 12 dollars repair place want 110 to come look at it this site walks you through repair best service!!!!

Ordered new racks and replaced them.

The hardest part was pulling the oven away from the wall. Two bolts hold the sensor in place and a clip connects the electronics. Replacing the old one was trivial.

Apparently, the original insulation had been removed due to a mouse infestation-the unit had been in storage for a while. After removing about 50 screws, I had all the body panels off and cleaned out the interior of the stove then installed the new insulation. I put it all back together and hooked it up- works just like new. I only paid 6 ... Read more 0 bucks for this oven, so all in all, not a bad deal.

My Tappan Tail:

Open the oven and remove the racks, turn on the oven light.
Remove two screws in the back to remove the bottom plate. Mine are about 1 1/4 in. long.
Remove one nut holding the butterfly plate in place. Ignitor will be exposed.

Turn off the oven light and unplug oven. Don't drop the plug behi ... Read more nd the oven, I was ready for that one.
Drop light or flash light will be needed, it's dark in there. And something to sit on, 16" old plastic milk caddy, I just happen to have one.

Remove the two screws holding the ignitor, don't cut the wires just yet. Take note where the wiring runs. Install the new ignitor. My wires went behind the gas piping.

I cut the bottom wire from the old ignitor first, up close to the ceramic. Wire shield can be reused, slide it over the new wire. Cut the old wire, leave a lot. Trim the new wire to desired length and strip the ends of both and use the ceramic cap and connect the wires.
Do the top wire.
Slide the wire shield next to the igniter, adjust the wires so the wire shields won't slide away from ignitor. With the butterfly shield back in place it's time to plug it in and give it a test.
Nice.
Replace the bottom plate of oven, screw holes hard to find. Had to use an awl to find the holes to line up the screws. I also didn't push the front of the plate down into place until I had the screws started. It helped.

You might think this is overkill, but how many of us have ever replaced the ignitor. Not me.
I do a lot of DIY's. I'll rate this as a 1, easy.

What shall I bake first, cornbread of course. I my cast iron skillet.

The repair went relatively easy especially after reading that another homeowner found the door to be "spring loaded". I was prepared and made sure I held onto things tightly.I removed the screws as I came to them and carefully removed the other 3 pieces of glass, finally reaching the inner panel. Putting that in and holding it as I put t ... Read more he next piece back was the most difficult. Once that was in place, the rest was just a matter of redoing what I undid. Needless to say, I was a bit nervous the first time I used the oven. No problems though, works like a charm! Thanks!

First of all I would like to comment on how it easy it was to place this order and I was pleasantly surprised that it was rec'd the next day. Also it was the correct part that I needed. To install it, first I removed the screws and then the metal that was holding the broken glass. Once the broken glass was removed, I set the new glass ... Read more in the metal strips and basically screwed it back together. Please note to be careful to remember which screws go where as they are not the same size and do not fit anywhere but where they belong. That was the only part of the job that I had a problem with.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

I took the brads that were left from the old gasket off with needle nose pliers. Then I put the new one on. It was very easy.

The range top had to be taken off along with the front panel to get access to the place the burner pipe connects. It took more time to unassemble and assemble the range than repacing the burner. The only issue was that the burner was sent without the bolts that will hold it in place so I had to go to local hardware store to get appropriat ... Read more e bolts.