TGF326WHTD Tappan Range - Instructions

order pcs fit perfect.

The stove was older so the burner was hard to get out. The small screw heads broke off, so I had to carefully center punch and drill out the screw bodies. The igniter screw was also frozen in the pot metal burner. That screw requied drilling and tapping with the installation of a new 6-32 screw. Once the burner was refurbished, the igni ... Read more ter mounted easily. Afte attaching the gas line and igniter wire, the burner worked great.

Disconnect appliance from electricity source! Removed oven grates and the solid oven floor by removing the two screws and lifting up. Removed the piece of metal covering the oven igniter. Unscrewed oven igniter, snipped the wires close to the old igniter (read some of the better descriptions on how to do this). Reconnected new wires to ... Read more the existing ones and used the ceramic wire covers that came with the new igniter and pushed the wires back through the opening in the rear of the oven. Screwed the new igniter in place. We actually had to unscrew the little metal box on the back of the oven to get to the wires which was easier to work there with connecting the wires. It was a little difficult reaching into the stove since we didn't remove the oven door.

First i want to thank you for the quick responce, i got my order in one day. Took top of stove off, took out the old part, put the new one in, made several test to adjust the heat settings put everything back together alls well, now my wife can cook things without burning everything, thank you from the bottom of my heart, a happy wife mea ... Read more ns a happy man. William L Zeis.

Checked internet for possible reasons why oven would not heat.

Found Partselect.com website. Searched and found that ignitor was probably the problem.

Put in my oven model number and found ignitor. Ordered ignitor.

When new ignitor came in I simply removed two screws that held old ignitor and disconnect ... Read more ed two wire.
Put new ignitor on, replaced screws and wires.

Repair done and oven works great.

Removed oven door. (Open to first position then lift the door straight up). Located igniter in bottom of oven, followed connecting wires to connection block below oven behind the oven drawer. Disconnected the existing wires. Lifted the burner out of oven to disconnect defective igniter. Screws were fused to the burner. Used vice grips ... Read more to remove screws requiring the screw holes to be retapped. Bought new screws to replace trashed screws. Installed new igniter to the burner rail then set burner rail back in place. Fished the leads from new igniter back down to connector block. Reinstalled leads. Reinstalled oven door. Tested functionality of oven. Everything worked. Reinstalled metal plates back in oven. Reinstalled cover over connection block behind bottom drawer. Reinstalled drawer. With the exception of fighting with two screws fused to the burner rail it is a very straightforward repair and shouldn’t take much more than 1/2 hour.

One night I found a mouse living in my stove. We found it literally living underneath the top of the stove (the part where the burners are that you have to lift up). The insulation on the inside of the stove was literally covered with mouse poop, dog food, dog treats, and scraps of food among other things. It was totally nasty and I thoug ... Read more ht we would have to buy a new stove. However, I searched online and found replacement insulation on PartSelects website and ordered it. It was cheap and the fix was removing old insulation, vaccuming out and cleaning the stove then replacing the insulation with the new one. PartSelect had a great price and shipped promptly.

Lifted top burner plate, removed all knobs, removed front plate that holds oven burner control. Removed burner control feedind thermocouple through hole at top of oven. Installed new oven control, fed t-couple back through hole and placed in holder. Put front plate back in place and re-installed knobs. Oven works great now, lights at 200 ... Read more * where as before would not light at less than 400* setting. Took only a straight blade and phillips screwdriver to do the job in less than 1 hour, that included cleaning the front plate and knobs while they wereoff.

First, I want to say how WONDERFUL your service was. I needed more info on a part and your phone rep. e-mailed me a picture of the part from which I was able to be sure it was the right part. I ordered the pard one day and they were delivered to my door the NEXT DAY....talk about service!!!

My husband did all the replacing ... Read more , he had no problems with any of the 3 items he replaced, he said they were all easy to replace. They all work great. Thank You!!

removed two screws disconnected inlet pipe and two outlet pipes, removed regulator. Replaced with new regulator. performed leak Test.

Our original oven ignitor went bad. The gas supply won't even open, unless the oven senses the proper voltage / resistance across the ignitor, so that gas won't be flowing without ignition.

PartSelect was very good about providing me with the proper part, after I got the part number from their schematics and wiring diagrams, ... Read more on the website. The first replacement part actually arrived, broken, from shipping, but when I called them, they immediately reprocessed the order, and sent me a new ignitor, to arrive the following day. I was very satisfied with their professionalism, as I've been in the past with them, as well.

On to the actual repair:

I removed the broiler drawer from the drawer slides, reached under the main oven chamber, unscrewed the two screws holding the ignitor in place, and cut / disconnected the two wires supplying the power to it.

I then put the new ignitor in place and screwed it back to the mount, used the wire nuts that came with the new ignitor to reconnect / splice the wires, and put the broiler drawer back in place.

Oven fired right up!

Entire process took less than 35 minutes. (Likely would've taken a bit longer, but this is the second replacement for the ignitor, since we've owned this oven, so I already had a good idea how to do it. (The first replacement for this particular part was NOT from PartSelect, so we're hopeful this one lasts a while longer than the previous one.)

Thanks, PartSelect!

no need to remover burner. Lift top up use a 1x4x5" to hold top up. Use short #2 screw driver remove screw and replace with new igniter

Slide out the old; slide in the new!

Make sure you unplug the oven before you begin. I removed the old igniter. The top wire on the igniter goes to the back of the oven and plugs into a flat blade type connector. Instead of using the twist wire nut I used a flat connector because it was easier to put on and is foolproof. Make sure you cut the plastic insulation off the c ... Read more onnector so it does not melt when the oven is in use. I used a wire nut on the other wire and that was it. Very simple and the oven works great again.

First I removed the two screws that held the clock in. Next I popped in the clock hooked up the wire connect, and screwed the screws back in.