TGF324WHSC Tappan Range - Instructions

open oven door remove bottom of oven then remome the metal cover over the burner to expose the ignighter remove 2 screws that hold it to the bracket. the two wire's that come out of the ignighter run down under the bottom oven pan, i removed the bottom front cover by lifting up and then pulled out, then i could see the wires i removed the wire nuts and pulled old wires off and removed old ignighter. i pulled off the insulator covers from the old one and slid them on the wires of the new ignighter then i fished the wires back down and and attachted them with the wire nuts, then reasembled the rest of the oven. woks great!

Removed lower drawer of oven and base panel of oven. Unplugged stove from outlet. Removed old igniter w/ nut driver (two screws). Disconnected wires (blade connectors) from stove base. Disconnected two-pole plug from oven after removing protective cover in corner.

Install new igniter. You will need to cut existing wires from old igniter so that spade and two-pole connectors can be reused. Join these wires with the new ignitor wires using the ceramic wire nuts provided with the new unit.
Directions are also provided with the new igniter.

1. Removed top over the oven burner.
2. cut the two wires conneted to the igniter about
an inch and a half.Noted which wire goes to the top of the igniter and which one went to the bottom.
3. unscrewed the igniter from the mount and
carefully pulled it from the oven.
4. put the new igniter wires through the hole.
5. mounted the igniter to the burner.
6. attached the new wires to the top and bottom old wires with the connectors that came with the igniter.
7. pluged the range back in and turned on the oven. Igniter works great.

After diagnosing the problem, I entered the Tappan Model #, found the part needed, and ordered from Part Select. On receipt (2 day delivery), I followed the instructions enclosed with the ignitor, and within 30 minutes, had everything up and running. Thanks PART SELECT!

moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.

Thank you, Thank you and thank you!!! I couldn't be happier and I save over $200 in repair. My repair was very easy after watching the video. I cut off the wire and ensure that the new one are attached into place. Placed all parts back and boom, the oven starts working a new.

First thing is I looked for videos on how to replace oven igniter to get an idea. Unplug AC cord and turn off gas valve.On my model I was not able to figure out how to remove oven door. You can still work around it without removing. Inside the oven, remove bottom cover. Remove 2 screws located in rear corners. After removing oven bottom cover, next is a burner cover. Remove 2 screws located toward front of oven using a nutdriver or socket. After removing burner cover , you will find oven igniter. Now remove bottom drawer. This is why its a bit difficult for others. Igniter has 2 leads. Laying down on the floor and reaching in to follow-identify where the 2 leads go to. Using same nutdriver or socket remove 2 screws that hold up the igniter. I cut the leads from the base of the old igniter so you will have some slack to work on when you reconnect the wires underneath. Install new igniter, run leads same way.Strip back about 3/8 in. wire, twist leads to proper wires and twist on ceramic wire cap that is provided. Make sure no bare wires are exposed! Now you can test.

I used the tutorial as a guide, and went ahead with the repair. Because of the older model I was working on there were many more screws to remove, not a problem the repair was simple.

AS YOU DESCRIBED IN YOUR YOU-TUBE VIDEO, THE OVEN IGNITER WOULD GLOW BUT THE OVEN WOULD NOT LIGHT. YOU EXPLAINED THAT THE PROBLEM COULD STILL BE THE IGNITER AND SO I ORDERED A NEW IGNITER AND THEN WATCHED YOUR VIDEO ON HOW TO ACCESS AND REPLACE THE NEW IGNITER AND THAT FIXED THE PROBLEM. I ONLY HAD TO CUT THE OLD WIRES ON THE OLD IGNITER AND MATCH WIRES WITH THE NEW IGNITER USING THE CERAMIC WIRE NUTS SUPPLIED, AND I WAS BACK COOKING AGIN. THANKS.

took of bottom pan and pan above the gas flame off and the igniter off , cut the two wires. replaced the igniter hooked the wires togther, replaced both pans. turned the oven on and it lite

First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires nuts, (from last repair) installed new igniter. Not rocket science here.

CUT THE WIRES ON OLD IGNITER AND WIRE NUT THE WIRES OF THE NEW IGNITER TO WHERE I CUT THE OLD ONE OFF.

Simple repair ,unplug unit,cut the 2 wires close to heating element,remove elements 2 screws w/1/4 inch nut driver. Cut and strip 2 wires back about 1/2 inch,be sure to cut wires close to element,wirenut both wires together. Reinstalled element,plug unit back in. Done . . . 12 Minutes,ready to bake a cake. .

First turn the thermostat off-cut the wires leading to the ignitor, close to the ignitor side-Remove the two 1/4" monting bracket screws and remove the ignitor install the new ignitor using the same 1/4" screws and reconnect the wires leading into the ignitor, note the polarity is not imp[ortant--use the heat temp-wire nuts provided--close the door and call for heat the gas valve is working fine now....

removed broiler front by depressing the indents on the door slides, removed two screws holding igniter cut wires on old igniter and spliced new igniter to existing wires with supplied wire nuts then reinstalled new igniter and tested have been using oven ever since