TGF317ESA Tappan Range - Instructions

Watched a half dozen You Tube Videos before I saw the Exact one-Submitted by a Woman-Super Easy-Had the Exact Part from this site!

Disconnected power cord to range
Removed the cover over the flame guard
Removed the Flame guard
Pulled out broiler drawer
Unscrewed the cover and disconnected the white plastic connector to the ignitor wires
Un crewed the two small screws to the ignitor and removed the old ignitor
Cut the two wires from the o ... Read more ld ignitor
Connected the new ignitor to the wires on the white connector
Installed the new ignitor
Reassembled parts dsassembled
Plugged in power cord

Works

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience ... Read more with those in need of you services. Thanks. Marilyn Kasson

First I removed the oven door from the range by removing 2 screws from the door. Next I removed 2 more screws from the oven door to get to the panel beneath. Once the top portion of the door was removed there were 4 nuts holding the glass sections together. Once these nuts were out I removed the broken class, replaced it with the new g ... Read more lass and reassembled. It was a very easy and quick project. I was so happy to find the part. I thought I was going to have to buy a new range. Thanks.

Got a copy of the parts breakdown for the oven door from partselect. Com. Removed 8 screws from outer frame (3 top, 3 bottom, 1 on eah side). Removed the main glass pane from oven door, be careful when doing this as this is most of the weight of the door. It will want close on its own due to lack of weight. Removed the 2 top screw ... Read more s that attach the handle. Removed some screws from some plates that retain the 2 panes of glass of glass. Removed the third (most inner, broken) pane of glass. Replaced with new one. Reversed disassebly procedure for assembly.

See other posts.... they have the correct repair procedures.

HIGHLY RECOMMEND removing the bottom drawer to access the space where splice will be made between new igniter wires and existing wires. This step is recommended in previous posts. I wasted a lot of time taking out unnecessary stuff in the oven compartment before I ... Read more realized that the drawer compartment provided easy access for repair. Story of my life on just about all repairs.

Remove bottom plates and deflector from oven, remove old igniter. Remove bottom drawer and panel to expose wiring. Cut wires, used supplied wire nuts to splice. The time consuming part of this job was having to clean all the parts before reassembly, and having to extract screws that were rusted into place due to heat and spillage. One ... Read more of the igniter screws was stripped, and was very difficult to remove. The first part in your "probably cause" list was the right one! Thanks for the good service, and a useful website!

This was very easy. Just remove the bottom of the oven by removing the two screw in the back. Then remove the baffle from under that and you of will see the ingniter. The one wire will reach the gas valve, just splce the other. 6 screws is all it takes. Turned it on worked perfectly.

Oven would not light upon setting for oven heat-up. Igniter would glow, but no gas flow. Gas Valve safety not sensing enough current draw from igniter to open gas valve. Original igniter measured 175 Ohms on Volt-Ohmmeter. New Igniter measured 74 Ohms before installation and use. Installed and spliced into existing wires using good qualit ... Read more y wire nuts and tucked wiring into wire areas ensuring it was away from burner flue. Oven lit on first start-up! Problem fixed! Easiest to get to by removing broiler drawer, pressing catch tangs in from outside rails using a small screwdriver. 1 screw of 2 on igniter mount was stripped and difficult to remove, but working with pliers and nut driver was able to remove it with some difficulty. New Igniter hangs fine with 1 screw. .

1- put in new thermostat 2- put in new gas valve 3- put in oven igniter ....3rd time a charm. Now I have all new oven parts! My husband installed and said it was pretty easy, have to take the oven door off and inside bottom out.

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

Pulled out broiler drawer, removed 3 bolts, plugged in new igniter. Only issue was one of the tiny bolts stripped, so now only have 2 holding it in place.

Remove oven racks and bottom oven panel cover.Removed old igniter.one screw was stripped so that slowed me down quite a bit! Used a small vise grip tool to remove screw! installed new ignighter,cut existing wires; spliced in new wires( be sure to unplug appliance) tested ok. Reassembled.

I loosened two screws(one on the left and one on the right) at the inside base of the oven door, then lifting the door off. The hinges are held in place by two screws and a flat metal covering. Remove the faulty hinges. The screw holes on the new hinges have to have some WD40 applied and then screw the screws in and out to widen the h ... Read more oles a bit. Once the screw goes in easily, remove them and insert the hinge into the hole that you removed the old hinges from. Replace the metal covering and insert the screws. tighten the screws. Open the hinges then slip the door back onto the hinges. Reinsert the two screws at the bottom of the door and tighten. I recommend replacing both hinges as there is a plastic insert in the hinge that becomes brittle over time and breaks.

I put in the part and it went well, I have used other parts from your factory for the same stove so I knew it was going to go easy. The part only required one screw.