TEF353ASF Tappan Range - Instructions

Disconnect power to Range at Electrical Service Panel control box. Remove 240 volt service electrical plug to range. Remove back top panel to expose element control switches. Remove element control switch to L.F. burner by first pulling off the control knob. You may need to use a large flat screw driver to pry behind knob to get it starte ... Read more d but it should come straight off. There are two screws revealed under knob that need to come off. Then the element control is easily, but carefully, removed out the back. Be careful you do not pull the "Hot Surface Indicator Light" switch off right above the element control switch. If you do, this will break the end off the plastic "Hot Surface Indicator Light" lens. If this happens you can still replace it but you will need to use super glue to make the "Hot Surface Indicator Light" switch stay connected to the clear lens. Install new element control in reverse order before gluing the "Hot Surface Indicator Light" switch as stated above or you will knock it off again. While holding the old element control in your hand with wires still attached, remove one wire at a time (making note of the location code for each wire) from old element control and install on new control. The new element control layout for the wire prongs will be different so you need to make sure you look for the code (like L1, H1, P) located on each prong location and put the same coded wire from old element control location onto new control prong code location. Reinstall new element control (with wires pushed fully onto prongs of new control) into panel with screws removed before. Reinstall knob, reinstall panel cover and reconnect range power plug. Restore power to Range at Electrical Service Panel control box With electric power restored, test element control by turning it on and see if it properly cycles on and off at different settings. If working properly you should be able to hear it click on and off and element heating and going off accordingly.

It was a replace racks not repair. No problem

i used a screwdriver to remove the old drip pans and broken surface element in addition to prepping the bracket for the door. It was extremely difficult for me to find these parts for the frigidaire oven but these fit perfectly! I was extremely pleased with how quick it was to replace or fix everything. I will definitely order again when ... Read more the other surface elements go!

snapped the new piece of plastic in its place and ta da, its fixed.

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

Just pulled the old cook top burner out and put the new one in .it took about 1 1/2 minutes

Took the drawer out, snapped the new glide in place, and replaced the drawer. Installation was simple with no tools required.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

After a brief discussion with CS about the electric stove part was shipped it arrived and I proceeded to install I found it needed to be installed sideways not up & down like the old one. The terminals did not line up so I put the black lead first and the purple lead last in doing that I burned out the switch??? was not easy to install as ... Read more the video showed his switch matched each wire? My installation was sideways??

I used good old commom sense to disassemble and reassemble the frame, handle, internal glass,and inter panel to reach and repace the cracked glass. I must admit I had two machine screws left over during reassembly, but found a home. It is important to identify where each and every screw belongs. This will cut down your repair time. I ... Read more thank PartSelect for providing great service and assisting me in my time of need.

Marv Dixon

I am 78 years old and I watched the how to video twice and then did it so if I can do it anyone can,oh and I am a woman

First took apart oven door. then took out broken glass and replaced with new glass.Put everything back together done.

This was my first time ever working with electrical issues. My husband is not physically able to do repairs now. Very easy fix. Just viewed video repair instructions and it went exactly as instructed. Within 45 minutes, I had my stove repaired and cleaned and back in working order!! Great results. My range is working perfectly again and M ... Read more ama is happy!!

It went easy, I ordered the part from another vendor, received it in 3 days and it only took about 20 minutes to install.
I do not recommend ordering from PartSelect!

I follow the video on your site