TDB652RBR0 Tappan Dishwasher - Instructions

replacing 2 wheels was a breeze. did not need the screws afterall.

All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.

Removed the old rollers with with screw driver. Used the original screws and washers, and reinstalled the new rollers. Had been having trouble with top dish rack metal slides popping out of the old rollers. I not that the replacement rollers are slightly larger and have slightly deeper groves for the slides. Have not had the new rollers installed long enough to see if they remedied the problem. Will know in a few weeks time. So far, so good.

The repair was simple. When the part comes, you may need a hairdryer to heat up the plastic a bit to get any kinks that may have happened during packaging or shipping, very easy 5 minutes. Removed the old gasket by hand, very easy, 1 minute. You will need to clean out the track that the gasket sits in. Mine had years of black gunk inside of it. You will need qtips or a small screwdriver with some tissues or papertowels, easy but took 15 minutes to clean out properly. Installed new gasket in the track, start at the top middle, there is a notch on the gasket so you know where the middle is. Installed by hand, just push bottom edge into the clean track, easy 5 minutes. Ran the dishwasher with no leaks. Very pleased with the result and how easy the gasket was to remove and install.

Removed bottom cover , PLACED TAPE ON SHARP EDGES OF ALL METAL!!!!!!! Pulled electrical connections off with long reach pliers , removed old split nut ,it was loose !!!!!! . Placed new nut into deep socket , started by hand until sung ,then attached small short 1/4 ratchet to socket and took two (2) turns . Reattached wires with long pliers, Tested on short cycle and nooooo,leaks !!!!!!!! SAVED HUNDREDS OF $$$$$$$. Replaced lower cover .ITS NOT ROCKET SCIENCES. GET AFTER IT !!!!! Bill.

At first remove the lower rack to give more room for you to lean over the inside of the dishwasher then remove the old gasket tub 90 inches long make sure that you know which side goes where, so that it will be easy to put the new one. Then press the gasket firmly on the side.Now you can start your dishwasher with no leak and saves you a lot of money for buying a new one.

First, open the dishwasher door and unscrew it from countertop or side of the cabinet. Second, close the dishwasher door and lock it. Thrid, pull entire washer out slowly. Fourth, remove old door spring on both side and replace with new one using needle nose plier. Fifth, unscrew drain hose from under washer and under the sink disposal and replace with new one. Sixth, run washer and ck for leak then push it back under the counter top...done

Removed two screws holding the dishwasher in place under the cabinet. Pulled the dishwasher out to expose the door springs. Removed the old springs and installed the new ones in just a few minutes. Pushed the dishwasher back into the cabinet and replaced the screws. Job done.

Removed the service panel below the door (4 hex-head screws), then reached in and took the old broken spring out (right side) and hooked the new one up.

Glad I bought 2 springs - the other one (left side) broke about a week after I fixed the first one! Replaced it the same way. Helps to have small hands - you can't really see where you're putting the springs but can feel where they should go.

In about 20 minutes, I was able to remove the front panel and access the springs. Besides a hard water line in the way, it was a snap.

very simple to do....attach spring to door...stretch to hole in frame and attach there...easy as 123

I removed two screws that hold unit to countertop,
just pulled out unit about two inches. Removed broken door springs. Installed new door springs and pushed unit back into place and installed the 2 countertop screws DONE.

used the pliers to grip the end of the spring, extended it and removed it from the door and frame. The install then followed. It takes longer to remove the front panel than to do the repair.

Removed the "kick plate" (4) screws. the hard part was attaching the springs to the door hooks. you cannot see them, have to go by feel. then stretch them to lower frame. attached the lower door trim piece with three screws.

I pulled the old door gasket out, cleaned the guck out and pushed the new one in it's place.