TCP-210 Tanaka Water Pump - Overview

The fuel pipe/fuel line assembly is a genuine OEM parts kit used in gas-powered outdoor equipment with dimensions of 5mm x 160mm. It includes a pipe or line, which carries fuel from the tank to the carburetor, and a rubber grommet which holds the fuel line in place. The grommet also has a flange that prevents it from being pulled into the...Read more body of your equipment. Over time the grommet may wear down and the fuel line can become brittle and crack causing fuel leakages and difficulty starting or running your equipment. Therefore, it is important to routinely inspect this assembly and replace it when it shows signs of wear. Before your repair, drain the fuel for your safety and to prevent contaminating the fuel tank. To install a new fuel pipe assembly, simply pull off the old grommet and detach the fuel line. Carefully insert your new fuel line into the new grommet and connect the line to the carburetor and the fuel filter inside the fuel tank on your equipment.

Also known as a priming bulb, this OEM replacement part is an individually sold rubber primer bulb. Since it is made of rubber, it will eventually lose its elasticity and crack or break,and need replacing. It is designed for use with a variety of different small engine equipment and is also known as a purge bulb. Pressing this primer bulb...Read more forces fuel through the fuel line and into the carburetor from the fuel tank. Once the carburetor is has a sufficient level of fuel, any excess fuel will be forced back into the fuel tank through the return line attached to the carburetor. If your primer bulb has a darker appearance or has lost its elasticity and does not return to its original shape, it means the rubber will likely soon crack, which will lead to fuel leaking into the engine and ignition system. To replace your primer bulb, simply remove the outside cover and primer bulb cover and replace the bulb within its housing.

This is a genuine OEM replacement part, it is sold individually. The Fuel Filter is inside of the fuel tank. Its purpose is to filter out dirt and other debris from contaminating the carburetor. It will at sometime become clogged and restrict the fuel getting to the carburetor,and will have to be replaced. We do have an article and vide...Read moreo on How to Replace the Fuel Filters in Your Outdoor Power Equipment.. You can see this by going to the front page of our site and clicking on Repair Center.

This item has been OEM sourced to ensure a high level of quality. The clip is intended to be used with trimmers and blowers from Hitachi and Tanaka. The metal clip is part of the fuel system. The clip is used to fasten the fuel filter and the fuel line assembly. This part is priced as an individual replacement part.

This is a genuine OEM sourced element-cleaner designed for Tanaka gas powered equipment. It is used to filter out dust and other contaminants from going into the engine. Please note, this foam element-cleaner is sold individually. To replace this filter you should only need a screwdriver. • Make sure to disconnect the spark plug • R...Read moreemove the cover screw • Take off the cover and replace the filter element • Reassemble and test the unit

It is a genuine part that is supplied by the original equipment manufacturer for Tanaka handheld lawn and garden equipment. The purpose of this assembly is to allow air into the fuel tank so that a vacuum is not created when the fuel is being fed through the fuel line. It is an identical replacement for a missing or a faulty part that was...Read more installed on a new unit. To ensure the proper replacement procedure, refer to the appropriate diagrams for your model. It is a high-quality air vent which is made of durable material and is sold individually. Replacing it is a simple task that should not require any special tools. Disconnect the old vent from the hose and connect the new one.

This is a genuine Tanaka replacement part that has been sourced from the original manufacturer to be used with trimmers, edgers, hedge trimmers, blowers, and gas powered drills. The plastic pulley is used to store the starter rope and to engage the starter cam. This item is sold as an individual replacement part.

This is an OEM part sourced directly from the manufacturer. The throttle lever is found in a Tanaka centrifugal pump. This part is a complete assembly made of high-quality plastic and metal, and is used to control the speed of the engine. You may require a wrench when replacing this item. The throttle lever is provided as an individual replacement part.

This is an original replacement part manufactured for use with outdoor power equipment. The recoil spring is used to provide tension to rewind the starter rope after pulling to start the engine. This spring is available as an individual replacement part and is also part of the starter assembly. Please see model diagram for associative parts.

The pump filter body attaches to the fuel tank. It is an OEM replacement part for use in bicycle engines, trimmers, drills, generators, and brush cutters made by Tanaka. This is available as an individual replacement part and is made out of metal and a felt material. It might require a screwdriver, a set of pliers, a socket set, and a nutdriver to replace this part if it becomes broken or torn.