EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

TC8700XYP1 Whirlpool Trash Compactor - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
15 Inch Compactor Bags - 15 Pack – Part Number: W10165295RP
$27.36
In Stock
15 Inch Compactor Bags - 15 Pack
★★★★★
★★★★★
(5)
Part #W10165295RP
Trash compactor bags are a practical way to discard your waste. Due to the extreme pressure of the compactor, trash compactor bags designed to handle the force are necessary. These bags are made from tough 2.5-millimeter, multi-laminate plastic, and the patented Slip-Grip design prevents the bag from slipping into the compactor bin. They measure approximately 15 inches wide x 15 inches high and are made from 50 percent post-consumer recycled plastic. This pack of 15 trash compactor bags is a genuine OEM replacement part, and will fit most rectangular 15-inch trash compactors.
Drive Gear Kit – Part Number: 882699
$77.75
On Order
Drive Gear Kit
★★★★★
★★★★★
(60)
Part #882699
This is the drive gear kit for the ram that compacts the trash inside your compactor. If your compactor ram is getting stuck, there is excess noise during its cycle, or if your compactor does not stop at the end of its cycle, the driving gear may be the issue. The gear is white, plastic and approximately 4.5 inches in diameter. This drive gear kit includes both gears, pin spring, retaining clip (c-ring), ram stop, ram cam, and instructions. Make sure to disconnect the power to your trash compactor before beginning the repair.
Washer Front Leveling Foot – Part Number: WPW10001130
$6.40
In Stock
Washer Front Leveling Foot
★★★★★
★★★★★
(5)
Part #WPW10001130
The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is important that when installing this part you are very careful, if not installed correctly your washer will be off balance which will then cause it to vibrate and/or shake during the cycle. The function of the adjustable foot is to keep your washing machine supported and to make sure that it is level at all times. The tools you will need for this repair include a pair of channel lock pliers, and a 9/16 wrench.
15" Compactor Bag Carrier with Easy Grip Handles – Part Number: 13030RP
$40.02
On Order
15" Compactor Bag Carrier with Easy Grip Handles
★★★★★
★★★★★
(10)
Part #13030RP
This 15 inch compactor bag carrier fits around the compactor bag inside the compactor and is used to easily lift and remove trash compactor bags once they are full. Simply place the reusable bag carrier in the garbage can before placing a new compactor bag in the bin. The easy-grip handles make removal easier once the bag is full. This piece also makes a good carrier for bringing in logs for your fireplace. This part fits most 15 inch compactors. For the full list of compatible compactors, check the list below. Compactor bags are sold separately.
Touch-Up Paint - White – Part Number: 72017
No Longer Available
Touch-Up Paint - White
★★★★★
★★★★★
(7)
Part #72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
Drawer Roller – Part Number: WP9871602
$17.15
In Stock
Drawer Roller
★★★★★
★★★★★
(6)
Part #WP9871602
This bearing roller may also be known as the wheel assembly or the container roller bearing, and it is a piece for your trash bin. The function of this bearing is to work in conjunction with your trash bin to allow the canister to roll free. For this repair you will need a nut driver, a pair of pliers, a screwdriver set, and an adjustable wrench. The most obvious symptom that will require you to replace this part is if your drawer is hard to open and/or close. Your appliance comes with two bearing rollers and it is sold individually.
Trash Compactor Single Metallic Shoulder Screw Size 832 X 3\8 – Part Number: WP780263
$7.47
In Stock
Trash Compactor Power Nut Kit – Part Number: WP9870163
$52.67
In Stock
Trash Compactor Power Nut Kit
★★★★★
★★★★★
(5)
Part #WP9870163
Includes everything pictured above.
Spray Paint - 12 oz. - White – Part Number: 350930
No Longer Available
Spray Paint - 12 oz. - White
★★★★★
★★★★★
(3)
Part #350930
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a protective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.
Dryer Support Roller Clip – Part Number: WP90296
$7.47
In Stock
Wheel Assembly - Kit of 2 – Part Number: 882688
$27.36
In Stock
Wheel Assembly - Kit of 2
★★★★★
★★★★★
(8)
Part #882688
This wheel assembly, or roller assembly, is for a trash compactor. The kit includes two wheels that are approximately 1 inch in diameter each. The wheels allow the trash compactor container to roll in and out of the appliance. You may have to replace the wheel assembly if the container does not roll smoothly. To access the existing wheel kit on your appliance, uninstall appliance from the cabinet, depress foot petal to lift the container off its track, and remove the container from the tracks. This kit is an OEM part sourced from the authentic manufacturer factory.
Trash Compactor On/Off Switch Knob – Part Number: WP4155141
$49.50
Special Order
Trash Compactor On/Off Switch Knob
★★★★★
★★★★★
(3)
Part #WP4155141
This knob may also be called a Key.

Manuals & Care Guides for TC8700XYP1

Click to download

Common Symptoms of the TC8700XYP1

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken Gear
21 of 22 people found this instruction helpful.
  • Matt from Houston, TX
  • A Bit Difficult
  • More than 2 hours
  • Screw drivers, Socket set
Trash compactor started making "bumping" sounds when the RAM went through a cycle and tried to come back up. Finally, one day heard a "pop" went the RAM traveled to the bottom. The gear broke in half. Purchased the gear parts "KIT" online and repair took 15 minutes. Easy to do. Unfortunately, this was not only problem. The "cause" of the gear breaking was the Momentary Start/Stop Switch was bad. It's failure led to the main switch not working. The unit could not tell when the RAM had reached the top of it's cycle. The other problem was that I didn't put trash in the compactor. Suggest HIGHLY to never operate the unit's RAM mechanism without the compactor being at least 1/2 full per the instruction manual. Running it empty can cause a major problem, such as the gear breaking/stripping.
Was this helpful?
Thank you for voting!
Large Drive Gear Failure (split in half)
17 of 19 people found this instruction helpful.
  • Mark from Littleton, CO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Socket set
Moved the compactor out from under cabinet, laid it on it's side, removed bottom casing (two nuts front, three back), remove compression pin from small drive gear shart, replace new small drive gear and install compression pin, loosen motor mounts to allow large gear replacement, remove circlip holding large drive gear to shaft, remove an d repace damaged gear, set gear clearance and tighten motor mounts, grease gears, replace bottom casing. .
Was this helpful?
Thank you for voting!
Drive Gear Broken
12 of 13 people found this instruction helpful.
  • clyde from Covington, GA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Replaced the gear and unit worked execpt the plunger hit the side of the garbage container. This appears the be the reason the gear broke in the first place. Defective assembly from the factory.

To correct I had to remove the newly installed gear system remove inside cardboard side cover, Remove the screws that hold the bea ring for the lift screw so I could remove the chain. After removing the chain I could adjust the plunger to be level and not hit the side of the garbage container on its way down.
Was this helpful?
Thank you for voting!