This part is known as a pulsator cap or washplate cap, and is designed for your LG washer. It fits over the washplate mounting bolt and prevents clothes from getting caught on the washplate during a wash cycle. It is round in shape, and approximately 3 inches in diameter.
This drain hose is a genuine OEM replacement part supplied by LG for use in their washing machines. It is a light gray pipe with a diameter of 1.25 inches. The drain hose is connected to the drain pump, and it is responsible for transporting water out of the washing machine after a cycle. If the drain hose is kinked, damaged, or clogged, ...Read morethe washer will leak, or you may find standing water in the drum at the end of the cycle. Each drain hose comes with a metal clamp for fastening.
This water-level pressure switch in your wash monitors and regulates the water levels throughout the fill, wash, and rinse cycles. You will usually find it inside the control panel or near the tub. It ensures that the washer uses the appropriate amount of water for each cycle and load type. This genuine OEM assembly includes not only the switch itself but also the accompanying air dome tube.
This part is the replacement switch assembly for your top-load washer. It contains the switch mechanism and the connecting wire that hooks the door latch to the electrical system of the washer. The lid switch holds lets your washer know when the door is latched, so it can begin the wash cycle. If the lid switch is damaged, it will not all...Read moreow the washer to run properly. Be sure to disconnect the washer from the power and water sources before you begin this repair. This part is sold individually and is a genuine OEM part sourced directly from the manufacturer.
This inlet valve assembly in your washer controls the flow of hot and cold water into the machine, opening and closing as needed during the wash cycle to ensure the drum fills with water at the correct temperature. This valve is usually at the back of the washer where the water hoses connect to the machine. If the inlet valve is malfuncti...Read moreoning, you may notice issues such as the washer failing to fill with water, slow filling, or water entering the drum when the washer is off. This genuine OEM replacement part, sourced directly from the original manufacturer, is sold separately from supply hoses.
This drain pump assembly is responsible for removing water from your washer during the drain cycle. It is typically at the bottom of the washing machine and connected to the drain hose. If it is damaged, you may notice water not draining properly, unusual drain cycle noises, or a failure to move to the next cycle. This is a genuine replacement part sourced directly from the original manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
leg broke off inside housing
5 of 12 peoplefound this instruction helpful.
thomas m from CARMICHAEL, CA
A Bit Difficult
Less than 15 mins
raised the front of washer by hand (literally) and placed two 2x4 blocks under front lip for support. reached up inside washer cabinet and unscrewed the broken leg piece upwards into the cabinet. this was the only way I could get the broken piece out without some specialized tool to reach it from the underside. replacement with the new
... Read more leg was a breeze.
Read less
Was this helpful?
Thank you for voting!
Drain hose had a pin hole leak external to washer
3 of 6 peoplefound this instruction helpful.
Terry from SIMI VALLEY, CA
Really Easy
30 - 60 mins
Screw drivers
Very close to the installation video online at Parts Select. Removed the back panel, unclipped the hose from the inner fitting and replaced with the rear hose. Why it didn;t leak on the inside is interesting as there was no clip on the at the inner fitting. The one difference from the existing install video online was that I didn't
... Read more have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).
Read less
Was this helpful?
Thank you for voting!
WATER WAS NOT SHUTTING OFF
3 of 17 peoplefound this instruction helpful.
cathy. from etna, OH
Really Easy
15 - 30 mins
Screw drivers
I HAD A CHAT WITH LG EXPLAINED THE PROBLEM . SAID IT WAS THE WATER SHUT OFF VALUE. V EVEN SENT THE PAGE WITH PART# TO ORDER ONLINE.