This part is known as a pulsator cap or washplate cap, and is designed for your LG washer. It fits over the washplate mounting bolt and prevents clothes from getting caught on the washplate during a wash cycle. It is round in shape, and approximately 3 inches in diameter.
This is a drain hose assembly for top-load models of LG washing machines. This hose specifically is used to allow water to drain from the tub to the drain pump of the washer. This hose is made of plastic and comes with two clamps to secure it within your washer, one on each end. If you notice your washer is leaking check to make sure if t...Read morehis hose is cracked or damaged, because it will need to be replaced immediately. This drain hose is an OEM part that is sold individually and will require you to disassemble part of your washer to replace it.
This water-level pressure switch in your wash monitors and regulates the water levels throughout the fill, wash, and rinse cycles. You will usually find it inside the control panel or near the tub. It ensures that the washer uses the appropriate amount of water for each cycle and load type. This genuine OEM assembly includes not only the switch itself but also the accompanying air dome tube.
This inlet valve assembly in your washer controls the flow of hot and cold water into the machine, opening and closing as needed during the wash cycle to ensure the drum fills with water at the correct temperature. This valve is usually at the back of the washer where the water hoses connect to the machine. If the inlet valve is malfuncti...Read moreoning, you may notice issues such as the washer failing to fill with water, slow filling, or water entering the drum when the washer is off. This genuine OEM replacement part, sourced directly from the original manufacturer, is sold separately from supply hoses.
This drain pump assembly is responsible for removing water from your washer during the drain cycle. It is typically at the bottom of the washing machine and connected to the drain hose. If it is damaged, you may notice water not draining properly, unusual drain cycle noises, or a failure to move to the next cycle. This is a genuine replacement part sourced directly from the original manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The right side hinge that holds the washer top door broke and needed to be replaced.
18 of 20 peoplefound this instruction helpful.
John from SAN JOSE, CA
Very Easy
15 - 30 mins
Screw drivers
Popped out the plastic "doors" that cover the metal actuators. Removed the metal actuators on both right and left sides of the door then unscrewed (3 screws each actuator) them from door frame. Slid the actuators out to enable the door to be removed. Unscrewed 2 screws on the top front of the washer which enabled me to angle the top of
... Read more the washer to expose the screws that hold the plastic hinges. Unscrewed the hinges (2 screws each) and replaced both of the hinges (I figured I'd do both of them now so I don't have to do it again for another 15 years). Put everything back together and all works like new.
Read less
Was this helpful?
Thank you for voting!
Broken hinge on lid
3 of 4 peoplefound this instruction helpful.
Charles from NEW LEBANON, OH
Really Easy
30 - 60 mins
Screw drivers
Looked on line for instructions, took my time and the repair went very easy. Just be careful not to drop screws in tub.
Was this helpful?
Thank you for voting!
Broken hinge part #MEF62462103
3 of 4 peoplefound this instruction helpful.
Gerald from CARLSBAD, CA
A Bit Difficult
30 - 60 mins
Screw drivers
On repair of (replacing one of the MEF62462103 hinges) the previous comments and instructions were good and fairly accurate. However, in addition to having to remove the two screws on the top front so the entire top assemble can be lifted, there are two short screws on the back of the washer towards the top on each side that need to be re
... Read moremoved. That way you can tilt the entire top up enough to get to the two underneath phillips head screws for each hinge. It’s okay to leave all the hoses connected and good to have a second person hold the top tilted up so you can get to the hinge screws. It took about 30 minutes to change one hinge for me and my helper.