T-250 Shindaiwa Trimmer - Overview

The Fuel Filter is a white and silver, individually sold, steel part. It reuires pliers to install and its installation is rated as Easy. The part attaches inside of the fuel tank and is used to clean the fuel of debris. It should be changed regularly. Check your owners manual for the recommended replacement schedule for your engine. ...Read moreIf the fuel is leaking or their is a blockage, you will know the part is broken and will likely need to be replaced. To check for small leaks, feel around for dampness and the smell of fuel.

This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends). This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.

This breather, also known as a fuel tank vent, is a genuine OEM replacement part used in trimmers and edgers. It is responsible for managing the pressure and air flow inside the fuel system, by acting as a valve for the fuel tank. It allows clean air to enter the tank, while preventing dirt and debris from entering as well. Over time, the...Read more breather can crack or become clogged leading to restricted air flow, inconsistent fuel supply, fuel leakage, hard starting, and engine stalling. Locate the breather on or near the fuel tank and disconnect the hoses and fasteners attached to it. Depending on your model you may need to remove the fuel tank to complete this replacement. Place the new breather in position and reattach the hoses and fasteners. Test the new part by gently blowing into the breather to confirm that the air flow is not restricted.

Genuine Shindaiwa replacement part, this item is sold individually. The Eyelet is installed in the spool housing of the Trimmers shown below. Most of the Trimmers are dual line, so two Eyelets are required. The Eyelet creates a smooth surface for the cutting line to exit the spool.

This individually sold fuel gasket is designed for use with handheld lawn and garden equipment and is the seal for the gas cap. This gasket is a genuine OEM part made of a composite material and will eventually become brittle because it interacts with gas and oil, meaning it will need replacing before it becomes debris in the fuel tank. T...Read morehis gasket not only prevents debris from entering the fuel tank, but it also prevents any leaks. To replace, simply unscrew your gas cap and remove the old gasket from the cap, and then replace it with the new.

This fuel cap assembly is a genuine OEM part and is designed for use with outdoor handheld power equipment. Replacing your fuel cap is as simple as removing the old one and screwing the new cap on. This fuel cap keeps the fuel within the tank during operation, preventing leaks, and ensures that no dirt or debris enter the carburetor, filt...Read moreer, fuel lines or engine. Made of plastic with a cork seal underneath, this fuel cap is sold as an individual part, and has an approximately 2-inch diameter.

This OEM metal washer is commonly used on a variety of different small engine/lawn equipment models and is sold individually. This washer is used to help evenly distribute pressure from the securing bolt or screw with the cylinder cover, to reduce any effects of vibration from the engine. If the connection between the securing fastener be...Read morecomes loose, or if you are replacing the fastener itself, it is recommended that you replace this washer as well.

This OEM Clip is a silver, steel part, which is sold individually. The part secures the fuel line to the fuel filter and is rated as Easy to install. You will know you need a new one if there is a leak around the hose where this clip is used to secure it, or if the fuel line detaches.

This is an OEM sourced replacement part used on Shindaiwa trimmers. Its purpose is to filter out dust and debris from contaminating the carburetor and engine. When replacing the filter you can open the package in comes in and put a bit of two cycle oil in the bag and let it absorb into the filter. Then remove it from the bag and squeeze i...Read moret with a paper towel to remove the excess oil. To replace this filter no special tools are needed. Simply remove the cover and replace the filter element.

This authentic part is designed for Shindaiwa handheld trimmers. It is supplied directly from the original equipment manufacturer. The button is pressed on the ground to extend the cutting line from the spool. It is an identical replacement for a damaged or a missing component that was installed on a new unit. To ensure the correct instal...Read morelation of the new part, refer to the appropriate diagrams of your model. One durable plastic button is included. To perform this repair no tools would be needed, remove the old and secure the new one.

A genuine item that is supplied by the original equipment manufacturer for use with Shindaiwa handheld lawn and garden equipment. It is an identical replacement for a missing or damaged lever assembly that the throttle cable is attached to, please make sure to check appropriate diagrams of your model for the correct location and applicati...Read moreon of this component. Keep in mind this durable part is made of plastic and is sold individually.

This is an authentic Shindaiwa replacement part that has been sourced from the original manufacturer to be used with trimmers. The plastic spool is used to store trimmer line within the cutting head assembly. This item is sold as an individual replacement part, please note tools may not be needed to install the spool.