T-18 Shindaiwa Trimmer - Overview

The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches and 14.19mm in height. This part is used to pump fuel from the tank to the carburator and is rated Easy to install. This part installs on...Read moreto the primer assembly. If the part dries out or starts leaking that means it is broken (likely due to fatigue or general wear) and must be replaced. Check the model number to ensure you are choosing the right part.

This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends). This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.

This breather, also known as a fuel tank vent, is a genuine OEM replacement part used in trimmers and edgers. It is responsible for managing the pressure and air flow inside the fuel system, by acting as a valve for the fuel tank. It allows clean air to enter the tank, while preventing dirt and debris from entering as well. Over time, the...Read more breather can crack or become clogged leading to restricted air flow, inconsistent fuel supply, fuel leakage, hard starting, and engine stalling. Locate the breather on or near the fuel tank and disconnect the hoses and fasteners attached to it. Depending on your model you may need to remove the fuel tank to complete this replacement. Place the new breather in position and reattach the hoses and fasteners. Test the new part by gently blowing into the breather to confirm that the air flow is not restricted.

Genuine Shindaiwa replacement part, this item is sold individually. The Eyelet is installed in the spool housing of the Trimmers shown below. Most of the Trimmers are dual line, so two Eyelets are required. The Eyelet creates a smooth surface for the cutting line to exit the spool.

This individually sold fuel gasket is designed for use with handheld lawn and garden equipment and is the seal for the gas cap. This gasket is a genuine OEM part made of a composite material and will eventually become brittle because it interacts with gas and oil, meaning it will need replacing before it becomes debris in the fuel tank. T...Read morehis gasket not only prevents debris from entering the fuel tank, but it also prevents any leaks. To replace, simply unscrew your gas cap and remove the old gasket from the cap, and then replace it with the new.

The Recoil Starter Assembly, aka the Recoil Assembly, is a kit that includes the pulley, a return spring, the starter cord, and the pawls which engage the flywheel to turn over the engine. The components of this assembly are constructed of steel and plastic. The kit can be installed with a screwdriver and is rated as "Easy" to install...Read more (Tip: line all the parts up to install). This kit starts the engine, and you will know it is broken if the pull cord will not retract, or the engine is not engaging after it is pulled. The rope may also break. When the part breaks due to fatigue or general wear, it must be replaced. The part attaches on top of the engine where the flywheel is located.

This OEM Clip is a silver, steel part, which is sold individually. The part secures the fuel line to the fuel filter and is rated as Easy to install. You will know you need a new one if there is a leak around the hose where this clip is used to secure it, or if the fuel line detaches.

This authentic part is designed for Shindaiwa handheld trimmers. It is supplied directly from the original equipment manufacturer. The button is pressed on the ground to extend the cutting line from the spool. It is an identical replacement for a damaged or a missing component that was installed on a new unit. To ensure the correct instal...Read morelation of the new part, refer to the appropriate diagrams of your model. One durable plastic button is included. To perform this repair no tools would be needed, remove the old and secure the new one.

This genuine OEM replacement part is specially produced for Shindaiwa and Echo handheld lawn and garden equipment. It is generally used to secure the muffler, for correct application of this hardware please make sure to check appropriate diagrams of your unit. This hex socket head bolt is made from durable metal and it is sold individuall...Read morey. When installing or removing this bolt you will need a hex key which is also known as an allen wrench.

This is an authentic Shindaiwa replacement part that has been sourced from the original manufacturer to be used with trimmers. The plastic spool is used to store trimmer line within the cutting head assembly. This item is sold as an individual replacement part, please note tools may not be needed to install the spool.

59" long and is 1/4 of an inch diameter.

The spring goes between the spool and the housing and is available individually. If this part becomes broken or bent it will need to be replaced. During installation, a wrench may be needed to replace the metal spring. This is an authentic replacement part sourced from the original manufacturer for use with Shindaiwa brushcutters and trimmers.