SV-2AE Echo Engine - Overview

This OEM Fuel Filter is a silver and white, steel/felt, part measuring about 1.25 inches in length and 3/4 inch wide. It can be installed with pliers and is rated as Easy to install by customers. This part attaches inside the fuel tank to clean the fuel of debris, and should be replaced during regular maintenance, check your manual for ...Read morerecommended replacement time. If the filter is leaking or it has a blockage preventing fuel flow, then it should be replaced. If the engine sounds like it is not getting enough fuel, then remove the filter and check it for blockage.

This piston ring is an authentic manufacturer approved replacement part. Is is commonly used on Echo gas trimmers/edgers. The purpose of a piston ring is to create an air tight seal inside the cylinder. A worn or broken piston ring will allow combustion gases to escape the seal and enter the crankcase. This would cause low compression and...Read more a loss of power. Replacing an o-ring should resolve this issue. This part is made out of metal and is sold individually. To complete this repair you will need a set of wrenches, pliers and a screwdriver. • Remove the air cleaner • Drain the fuel • Remove the air cleaner case • Remove the carburetor • Remove the intake insulator • Remove the spark plug • Remove the engine cover • Remove the insulator gasket • Remove the starter assembly • Remove the fuel tank • Remove the air duct • Separate the engine • Bind the engine • Remove the clutch • Remove the flywheel • Remove the starter pulley • Unbind the engine • Remove the muffler • Separate the cylinder from the crankcase • Remove the piston ring • Install the piston ring • Reassemble and test the equipment

This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends). This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.

This spark plug wire, also known as a spark plug coil or spark plug cap coil, is compatible with various makes and models of hand-held outdoor power equipment and is sold individually. This wire is installed within the spark plug boot and attaches to the spark plug for the ignition of your equipment. The spark plug wire is often exposed t...Read moreo extreme heat and excessive vibrations, so through normal wear and tear, it will likely break down. If your equipment is having difficulty starting or has general performance issues, the wire may be the reason why. To replace this wire, make sure your equipment is off before removing the wire and boot from the spark plug. Remove the boot from the wire and install the new wire within the boot before re-installing the boot back to the spark plug.

This is an authentic manufacturer sourced replacement part designed for use with Echo backpack blowers. This carburetor gasket provides an air tight seal between the carburetor and the insulator. Over time gaskets tend to deteriorate and would need to be replaced. It is made out of compound material and it is sold individually. You would need a screwdriver to replace this item.

This OEM metal washer is commonly used on a variety of different small engine/lawn equipment models and is sold individually. This washer is used to help evenly distribute pressure from the securing bolt or screw with the cylinder cover, to reduce any effects of vibration from the engine. If the connection between the securing fastener be...Read morecomes loose, or if you are replacing the fastener itself, it is recommended that you replace this washer as well.

This replacement spark plug cap is a genuine OEM sourced item designed for use on handheld lawn and garden equipment. It is used to insulate the plug and wire terminal. Over time rubber material can dry out and crack requiring replacement. Please note, this item is sold individually.

This replacement part is an authentic OEM screw designed for use with blowers and string trimmers. This is a standard hardware which has multiple uses based on equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To secure or loosen this screw you would need a phillips head screwdriver.

This replacement grommet is an authentic OEM item that is produced for use with Echo gas powered equipment. It fits in the fuel tank to secure the hose and seal the opening. Over time it may deteriorate and crack eventually requiring replacement. It is made from durable rubber material and it is sold individually.

This is an original Echo replacement part manufactured for use with outdoor power equipment. This special screw includes a washer and can be used with either flat or phillips head drivers. The screw has different applications, please see model diagram for part location and use. The screw is sold individually.

This manufacturer sourced replacement part is designed for use with Shindaiwa and Echo handheld lawn and garden equipment. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt. This is a standard hardware which will has multiple applications depending on your equipment. This lock nut is made from high quality metal and it is sold individually.

This is an authentic replacement part manufactured for use with Echo backpack blowers, edgers, and trimmers. The screw has multiple applications that vary depending on the model of equipment. This screw is sold individually, please see model diagram for part location and usage.