This ice and water filter helps reduce impurities in select side by side and bottom freezer refrigerators. Replace it about every six months, or when water flow slows, ice production drops, or the filter light turns red. Some older filter setups may need an adapter. Place a cloth under the filter before removal. Check the exact refrigerator model before ordering.
This temperature sensor, also called a thermistor, measures temperature inside the refrigerator or freezer and sends readings to the main control board. The board uses this information to control cooling, including compressor and fan operation. Incorrect readings may cause the compartment to become too warm or too cold, or make cooling ru...Read moren longer than needed. The replacement includes the sensor body and wire leads. Its location varies by appliance. This is an OEM part sourced directly from the manufacturer.
This defrost termination thermostat (Defrost Limiter Thermostat, High Limit Thermostat, Refrigerator Defrost Bi-Metal Thermostat) acts as a safety device to stop the evaporator coil from overheating, by turning off the defrost heater at the end of the defrost cycle. This part attaches to the tubing of the evaporator coil in the freezer. A...Read more faulty defrost termination thermostat may result in the defrost heater never heating and a solid frost buildup on the evaporator coil, which results in too warm temperatures. The thermostat contacts are normally closed and have continuity until it reaches 140 degrees. If this high limit thermostat is open at room temperature or colder, it is defective. This limit thermostat has an attached mounting clip and comes with pink and amber wire leads. The thermostat is 1 inch in diameter and 1/2 inch thick, the 2 wire leads are 10 inches long.
This refrigerator ice maker assembly automatically freezes water and releases crescent-shaped ice cubes into the storage bin. It replaces an existing ice maker that has stopped cycling, fails to release ice, or has damaged components. Poor ice production can also result from a restricted water supply or incorrect freezer temperature, so c...Read moreheck these conditions before replacing the assembly. Confirm the mounting arrangement, fill cup position, electrical connections, and included adapters against the appliance parts list to ensure the kit matches the original installation. This is an OEM part sourced directly from the manufacturer.
Warm, moist air stays out of the ice chute when this refrigerator dispenser door flapper closes against the opening. The flap opens during ice dispensing, allowing cubes to pass through, then returns to form a seal when dispensing ends. A cracked, warped, or damaged sealing edge may leave gaps that contribute to frost, condensation, or dr...Read moreipping around the chute. Replacing a damaged flapper helps restore proper closure and reduces air leakage between the freezer and room while the dispenser is idle. This is an OEM part sourced directly from the manufacturer.
This red evaporator fan grommet cushions the fan motor where it meets the mounting bracket inside the freezer. It measures approximately 1 inch in diameter and helps reduce vibration transferred from the running motor. Wear, tears, or damage may contribute to buzzing or rattling from the fan area. Inspect the grommet, bracket, and fan bla...Read morede before replacement, since loose parts or blade contact can cause similar noise. The grommet sits behind the evaporator fan cover. Disconnect power before accessing the assembly and follow the mounting instructions for correct placement. This is an OEM part sourced directly from the manufacturer.
This ice dispenser solenoid moves the linkage that opens the ice chute door when dispensing is activated. When power is released, the mechanism allows the flap to close and limit warm air entering the freezer. A failed or sticking solenoid may prevent ice from dispensing or leave the chute door open, contributing to frost or moisture buil...Read moredup. Inspect the solenoid, spring, and door linkage before replacement, since other mechanism faults can cause similar symptoms. Disconnect power before accessing the dispenser assembly and follow the appliance instructions for mounting and wiring. This is an OEM part sourced directly from the manufacturer.
This electronic board (Main Control Board Assembly, Control Board, Motherboard) controls the temperature and defrost functions of the unit. This control board is located on the back of the refrigerator, and measures 8 inches by 5 inches. It’s constructed of metal and plastic, and comes in green. This kit includes one main control board wi...Read moreth built in defrost controls. If broken due to electrical surges or normal use, your fridge may experience temperatures that are too warm or too cold, or inconsistent defrost cycles. If this happens, the part should be replaced.
This defrost heater and bracket assembly melts frost from the evaporator coils during the automatic defrost cycle. Clearing the frost allows air to move across the cooling surface and through the refrigerator compartments. A failed heater may allow ice to build up, restricting airflow and leaving the fresh food or freezer section too warm...Read more. The appliance may also run longer without reaching the set temperature. Confirm the heater fault before replacement, since the thermostat and defrost control can cause similar symptoms. Disconnect power before accessing the assembly. This is an OEM part sourced directly from the manufacturer.
This is the replacement dairy door for a refrigerator. It is installed on the inner door and rotates up and down to allow access to the dairy compartment. It is made of clear plastic. If your dairy door is cracked, broken, missing, or won't stay on, you may need to replace it. This is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Leaking water valve
8478 of 12456 peoplefound this instruction helpful.
James from Centerville, OH
Easy
Less than 15 mins
Nutdriver, Socket set, Wrench (Adjustable)
Removed black cardboard covering on back of refrig with nut driver (6 screws), turned off water supply to pump, removed cooper waterline to pump with adjustable wrench, removed 1 screw holding pump to refrigerator, removed plastic waterline from pump by turning hose counter clockwise. Inserter plastic water line in new pump by screwing li
... Read morene in clockwise, pushed orange plastic stop around waterline into pump, connected cooper water line to pump first wrapping threads on pump with teflon plumbers tape, reinstalled pump to refrig and cardboard back on refrig with 6 screws.
One side note:.
This is the second pump which has burst at the blue plastic seam in seven years.
Read less
Was this helpful?
Thank you for voting!
Fridge too warm, evaporator icing up
606 of 738 peoplefound this instruction helpful.
Gerald from San Clemente, CA
Easy
15 - 30 mins
Screw drivers
After replacing the defrost heater, main board and thermistor I still had the same problem. Called a repair guy and he (with the help of GE on the phone) diagnosed that the temperature sensor was bad. So I ordered from partselect and installed it and it fixed the problem. Been good for a couple months (knocking on wood). To install I
... Read morehad to cut the 2 wires to the old sensor, crimp the 2 new wires on and snap the new sensor to the clip on the evaporator. Very easy. Make sure you seal the ends of the wire crimps so moisture doesn't get in and corrode the connection.
The refrigerator made continous "whooing" sounds that increased and decreased in pitch. Sounded like a ghost. Would keep us up at night. Also noticed that the heater was not heating under the evaporator coils.
561 of 652 peoplefound this instruction helpful.
John from Holly Springs, NC
Really Easy
Less than 15 mins
Nutdriver
After checking the stories, the consensus of opinion was to change the mother board. I had a tremendous help from Tom Paone at [email protected]. He also told me to change the motherboard but to make sure that the coils were totally defrosted before starting up the refrigerator after changing the board.
Took off thr
... Read moreee nuts around the board at the back of the unit. Removed the input wires and you have to push in the plastic tabs holding the board in. Then just put the new board in place and push till the tabs click. Re-install the wires and put the cover back on.
Really simple task,
It is now a week since doing this and the unit is working perfectly. No soulds and good nights sleep. The ghost has moved on.