EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

SSEH07WJ1500 Speed Queen Dryer - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Retaining Ring – Part Number: WP23748
$12.85
In Stock
Retaining Ring
Part #WP23748
The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place or is damaged. Some the symptoms could be that your dryer does not tumble, it makes a loud buzzing noise, or if it pumps, but will not spin. The tools needed for this project are a putty knife, 5/16 nut driver, and snap ring pliers. Refer to the installation video and diagram for further instructions and guidance. Customers ranked this replacement project as easy.
Cylinder Felt Seal – Part Number: WP37001132
$45.29
In Stock
Cylinder Felt Seal
★★★★★
★★★★★
(9)
Part #WP37001132
This cylinder felt seal is used in dryers and is located between the back of the drum and the rear dryer panel. If your dryer is experiencing any of these symptoms, replacing the felt seal could solve your problem: squealing or banging noise, clothes are getting stuck between tub and felt pad, takes too long to dry, not heating enough or not heat at all, or does not tumble. The tools needed for this installation are a 5/16 nut driver and a putty knife. Make sure to unplug the dryer from the power source before beginning this project. Refer to the manual provided by the manufacturer for further instructions.
Thrust – Part Number: WPW10121334
$7.47
In Stock
Spring Retaining Clip – Part Number: WP22001650
$9.62
On Order
Spring Retaining Clip
★★★★★
★★★★★
(3)
Part #WP22001650
This spring retaining clip is just under 1 inch long. The clip is made entirely of metal and is attached to the back wall of the washer, under the console. If your washer is vibrating and louder than usual during the wash cycle, your spring retaining clip could be faulty or damaged. Check the clip for visible damage, wear, and rust. If you notice any signs of damage, the part should be replaced. Remember to disconnect the power from your washing machine before starting this repair.
Washer Screw 818 X 1/2 – Part Number: WP3390631
$7.47
In Stock
Washer Screw 818 X 1/2
Part #WP3390631
This screw is sold individually.
Glide Bracket Kit – Part Number: 12002090
$79.10
Special Order
Glide Bracket Kit
Part #12002090
This kit contains two glide brackets and four screws.
Dryer Screw – Part Number: W10815455
$7.47
In Stock
Dryer Screw
Part #W10815455
This tapping screw is sold individually.
Screw – Part Number: WP27001200
$7.47
In Stock
Screw
Part #WP27001200
Sold individually.
Refrigerator Screw – Part Number: WP489464
$9.62
In Stock
Refrigerator Screw
Part #WP489464
Sold individually.
Dryer Screw – Part Number: WP3177991
$7.47
In Stock
Dryer Screw
Part #WP3177991
Sold individually.
Dryer Nut – Part Number: WPW10139757
$7.47
Special Order
Dryer Nut
Part #WPW10139757
Sold individually. This nut is for dryers. Follow appropriate safety practices when installing the nut.
COMPLETE R – Part Number: WFR500824
No Longer Available
COMPLETE R
Part #WFR500824

Common Symptoms of the SSEH07WJ1500

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
belt was cracking and dryer was somewhat noisy
4 of 7 people found this instruction helpful.
  • Melody from Silverton, CO
  • Easy
  • More than 2 hours
  • Nutdriver, Screw drivers
I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, rol ler, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.
Was this helpful?
Thank you for voting!
Cylinder Seal came out
4 of 8 people found this instruction helpful.
  • Marcia from Hammond, LA
  • Easy
  • Less than 15 mins
  • Pliers
Early in the life of my dryer, the Cylinder Seal came out. For the past two years I put off buying the part. When it came in, I p[opped the top of the dryer, removed the two screws holding on the front panel, and pulled the Cylinder of the back wall of the dryer. I then placed the seal in the right spot, glued it down and reassembled. About Fifteen minutes of work and a cheap part, and now my dryer dries a l;oad of clothes in an hour instead of three.
Was this helpful?
Thank you for voting!
Worn Felt Seal
3 of 5 people found this instruction helpful.
  • robert from hillsborough, NC
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
remove bottom two screws on lower front panel, remove panel. remove two screws on lower portion of door panel, pull bottom panel towards yourself to release pins at the top. Disconnect wiring for light and door switch (make sure to note what wires go where. Complete removal of front door panel. Remove 4 screws holding cylinder frame in place, lift to remove. remove remnants of old felt seal, use rotary tool to remove excess glue, etc. apply glue (used rubberized gorilla super glue), apply felt seal - allow glue to set up. reinstall in reverse direction from removal. Be sure to use glue as there are no clips or other retaining pieces for the new felt and it will not hold in place. overall pretty easy.
Was this helpful?
Thank you for voting!