The ice maker cube tray holds the water that comes from the ice maker during the process of it becoming ice. This part is white in color and made of plastic. All you will need for this repair is a flat blade screwdriver. Over time, the tray may bend out of shape or mineral deposits build up inside, which makes the ice stick to the tray. Y...Read moreou will find the ice maker underneath the ice bin in the freezer. Use your flat-head screwdriver to release the tab holding the ice maker in place, this will expose the ice tray.
This evaporator fan motor is in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. When the evaporator fan motor fails, it often generates a lot of noise in the freezer area. If you notice that your refrigerator or freezer is noisy, or is not ...Read morecooling like it should, you may need to replace the evaporator fan motor. The base of this part is approximately 3 inches in length and 2 inches in width. The shaft of this part is an additional 2 inches in length.
This sensor cover, also known as the ice maker thermostat cover, is a genuine OEM replacement part for Samsung refrigerators. It is made of durable white plastic and has measurements of approximately 2.25 inches by 1 inch. The sensor cover is responsible for protecting the ice maker thermostat from contaminants, ice build-up, water, and m...Read moreoisture which can prevent the thermostat from regulating the ice maker temperature properly. If your ice maker is producing ice very slowly and you also notice large clumps of ice in the ice tub, then the sensor cover is likely damaged, or it has fallen out of place. You will need to remove the freezer drawers to replace this part.
This genuine OEM water filter is made for your side-by-side or French door refrigerator, working to reduce impurities like iron, chlorine, and rust for better-tasting water. With a capacity of 300 gallons, it is easy to install with a rear mount design, saving space in your fridge. If the filter gets damaged or clogged, you might notice s...Read morelower water flow or odd tastes. We suggest swapping it out every six months. Sign up for our water filter subscription plan for automatic replacements.
This condenser fan blade (part number DA31-00010D) is for refrigerators. Condenser fan blade DA31-00010D moves air across the condenser coil to cool the hot refrigerant before it enters the evaporator. Safely store any food that could deteriorate while the power is off and unplug the refrigerator before installing this part.
This roller wheel axle pin (part number DA61-01920A) is for refrigerators. Roller wheel axle pin DA61-01920A attaches the roller wheel to the roller wheel bracket. Wear work gloves to protect your hands during the repair.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
freezer was cold fridge was not
16 of 33 peoplefound this instruction helpful.
theodore from PUEBLO, CO
Really Easy
30 - 60 mins
Screw drivers
Took shelving out of freezer removed panel. Took second panel out and removed motor. Whole repair took 45 minutes. Works perfect
Was this helpful?
Thank you for voting!
Ice maker not functioning properly
2 of 3 peoplefound this instruction helpful.
Bill from Tucson, AZ
Easy
15 - 30 mins
Screw drivers
Barely losened the two rear screws. Took out the two front screws and the ice maker slides toward front of fridge off the 2 rear screws. Unhooked the wiring plug. Replaced with new ice maker.
Was this helpful?
Thank you for voting!
Lever Dispenser-Ice Was Broken.
0 of 2 peoplefound this instruction helpful.
RUSSELL from LAS VEGAS, NV
Easy
15 - 30 mins
Screw drivers
Using the putty knife, pry off the faceplate for the ice/water dispenser. Disconnect the wire harness. Using philips head screwdriver, remove the dispenser assembly. Remove the old dispenser and replace. Reverse for reassembly. Note * I should have bought the water dispenser lever and replaced it as well since I had the assembly out.
... Read more Secondary note * be mindful during reassembly to not put pressure on the water dispenser or have a glass handy. :)