The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches and 14.19mm in height. This part is used to pump fuel from the tank to the carburator and is rated Easy to install.
This part installs on...Read moreto the primer assembly. If the part dries out or starts leaking that means it is broken (likely due to fatigue or general wear) and must be replaced. Check the model number to ensure you are choosing the right part.
This a a genuine OEM replacement check valve for your small engine. It is also known as a fuel tank vent. You may need to replace this part if you are noticing debris or dirty oil in the reservoir. Make sure the engine is cool before you begin this repair, and remove the wire and boot from the spark plug to prevent the engine from starting up.
This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends).
This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.
This is a genuine OEM sourced replacement part designed for use with Echo blowers/trimmers. This is a standard hardware which has multiple applications based on your unit. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To remove or install this screw you would need a screwdriver.
This spark plug wire, also known as a spark plug coil or spark plug cap coil, is compatible with various makes and models of hand-held outdoor power equipment and is sold individually. This wire is installed within the spark plug boot and attaches to the spark plug for the ignition of your equipment. The spark plug wire is often exposed t...Read moreo extreme heat and excessive vibrations, so through normal wear and tear, it will likely break down. If your equipment is having difficulty starting or has general performance issues, the wire may be the reason why. To replace this wire, make sure your equipment is off before removing the wire and boot from the spark plug. Remove the boot from the wire and install the new wire within the boot before re-installing the boot back to the spark plug.
This trimmer shield assembly is designed to protect the operator by deflecting grass, dirt, and debris away from the cutting area during trimming. Made from durable, impact-resistant plastic, it helps improve safety while also shielding key components from damage. Many versions include an integrated line-cutting blade to keep trimmer line...Read more at the proper length for consistent performance. Ideal for replacing a cracked or missing guard, it restores safe operation and dependable trimming control.
This OEM metal washer is commonly used on a variety of different small engine/lawn equipment models and is sold individually. This washer is used to help evenly distribute pressure from the securing bolt or screw with the cylinder cover, to reduce any effects of vibration from the engine. If the connection between the securing fastener be...Read morecomes loose, or if you are replacing the fastener itself, it is recommended that you replace this washer as well.
This replacement screw is specially designed for use with Echo handheld lawn and garden equipment. It is a high quality OEM sourced item, not an aftermarket imitation. This screw is a standard hardware which has multiple uses depending on the equipment. Please note, this hex socket head screw is sold individually.
This is a simple adhesive sticker/decal with Echo logo. It is commonly used on handheld lawn and garden equipment such as trimmers and blowers. Please make sure to check appropriate diagrams of your model to check the location for this label. It is an authentic manufacturer approved replacement item which is sold individually.
This replacement gasket is a genuine OEM sourced item that is designed for Echo handheld lawn and garden equipment. It is a high quality rubber item that helps to create a tight seal between the fuel tank and the cap. Please note this cap gasket is sold individually.
This control-throttle is a genuine OEM sourced item designed for Echo handheld lawn and garden equipment. This is the plastic lever that allows user to control the throttle. It is made from durable plastic and it is sold individually. You will need a screwdriver to replace this part.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Echo trimmer had narrow shield. Bought wider one which reduced rocks and debris
5 of 9 peoplefound this instruction helpful.
Robert from COEUR D ALENE, ID
Very Easy
Less than 15 mins
Screw drivers
Easiest repair ever. Turn the trimmer upside down so you can access the string assembly. Find the small hole in the shaft beneath the string assembly and insert a heavy gauge nail into it to hold the shat in place. Turn the string assembly counterclockwise until it comes off. Lift off the round metal piece that was under the string assemb
... Read morely.Find the 3 screws holding the shield in place and unscrew them. Pull the shield off. Install the new one in reverse order. I used the original hex screws as the new ones were philips head. Hex worked perfectly. I was amazed how easy thus was to do.
Read less
Was this helpful?
Thank you for voting!
I was missing the label for the choke on the air filter.
1 of 4 peoplefound this instruction helpful.
Aidan from THOMASTON, ME
Easy
15 - 30 mins
I made sure everything was lined up and stuck it on.