This OEM Fuel Filter is a silver and white, steel/felt, part measuring about 1.25 inches in length and 3/4 inch wide. It can be installed with pliers and is rated as Easy to install by customers.
This part attaches inside the fuel tank to clean the fuel of debris, and should be replaced during regular maintenance, check your manual for ...Read morerecommended replacement time. If the filter is leaking or it has a blockage preventing fuel flow, then it should be replaced. If the engine sounds like it is not getting enough fuel, then remove the filter and check it for blockage.
This a a genuine OEM replacement check valve for your small engine. It is also known as a fuel tank vent. You may need to replace this part if you are noticing debris or dirty oil in the reservoir. Make sure the engine is cool before you begin this repair, and remove the wire and boot from the spark plug to prevent the engine from starting up.
This is the replacement vent tube for your outdoor power equipment. It is made of black plastic and is approximately 3 inches long and ¼ inch thick. The vent tube allows air into the fuel tank so that a vacuum is not created when fuel is being fed through the fuel line. The vent tube is often connected to the fuel line grommet that is ins...Read moretalled on the fuel tank. If the vent tube is broken or missing, it can lead to decreased engine power and performance. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
This fuel pipe or fuel line is designed to deliver fuel to the carburetor from the fuel filter inside your tank. It is black in color, made of rubber, and its dimensions are 3x5x180mm. The fuel line is sold individually. If you notice fuel leaking from your fuel line, it could be cracked due to wear or drying out, and will need to be repl...Read moreaced.
Our customers rated this repair as easy, it does not require any special tools. Attach the new fuel line inside the tank onto the fuel filter and the carburetor.
This genuine fuel clip is a silver, metal, individually sold part. It can be installed with pliers and is rated as Easy to install by customers.
This part attaches to the fuel filter to secure the fuel line ot the fuel filter. If broken, likely due to fatigue, there may be a fuel leak. If damaged or missing, the part should be replaced. ...Read moreRefer to your owners manual or model number to ensure you are choosing the correct part.
This is a genuine manufacturer approved replacement part designed for use with edgers and trimmers. The purpose of this part is to act as a seal for the insulator. This item is made out of compound material and it is sold individually. To complete this repair you would need a screwdriver.
Also referred to as a Spark Arrester, this Spark Arrester Screen is an authentic OEM replacement part that is not part of a kit or assembly. It is made of metal and sold individually. The purpose of this screen is to prevent flammable debris from entering the engine and becomes worn through regular use. If the screen is clogged, remove th...Read moree screen from the muffler, hold it with pliers, and use a torch to burn off the debris before reinstalling the screen.
This part needs to be replaced when it becomes damaged or worn. When the screen is malfunctioning, you may notice debris exiting through the muffler. To complete this repair, you will need a screwdriver and pliers. This screen is located within the muffler; refer to your owner's manual for the exact location on your model.
Customers rated this repair as Easy.
The m10 Left Hand Thread Nut is a 10mm, gold metal part, sold individually. This nut is a "reverse thread". It requires a wrench or socket set to install, and installation is rated as "Easy". Use this part to secure the blade to the unit, by attaching it to the shaft, securing the cutting blade. If broken or damaged, it should be replaced...Read more. Refer to your make, model and diagrams to check if this is the right part for you.
The Cotter Pin (or Split Pin) is a 2x22mm silver metal part, sold individually. It is rated as "Easy" to install, and installation will require a set of pliers. It can be attached in various locations on a variety of equipment and is used to secure and lock parts in place. If broken, damaged, or worn down the part it is securing may becom...Read moree loose, and the part should be replaced. If this part is removed for repairs, replace it with a new one. Refer to your make, model, and diagrams to make sure this is the correct part.
This OEM replacement air filter is responsible for preventing dirt, debris, and other contaminants from entering and damaging the engine in outdoor power equipment. If the air filter is torn or clogged, less air will flow into the engine, the engine will overheat and produce more harmful emissions, you may have difficulty starting your eq...Read moreuipment, the engine components may be irreparably damaged. Replacing the air filter is an important part of maintaining your equipment, so ensure that you regularly inspect and replace it as necessary. Remove the dirty/damaged air filter, and thoroughly clean the housing. Place the new filter in and secure it with the filter cover.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Echo trimmer had narrow shield. Bought wider one which reduced rocks and debris
5 of 9 peoplefound this instruction helpful.
Robert from COEUR D ALENE, ID
Very Easy
Less than 15 mins
Screw drivers
Easiest repair ever. Turn the trimmer upside down so you can access the string assembly. Find the small hole in the shaft beneath the string assembly and insert a heavy gauge nail into it to hold the shat in place. Turn the string assembly counterclockwise until it comes off. Lift off the round metal piece that was under the string assemb
... Read morely.Find the 3 screws holding the shield in place and unscrew them. Pull the shield off. Install the new one in reverse order. I used the original hex screws as the new ones were philips head. Hex worked perfectly. I was amazed how easy thus was to do.