SN65 Senco Nailer - Overview

This is a genuine Senco replacement part, it is sold individually. Its purpose is to retain or secure the Retaining Pins in the Senco models below. It is attached to the pins by pressing them on the beveled end of the pins.

This is an authentic replacement part that is supplied directly from the original equipment manufacturer for use with Senco nailers. It is the special component which helps to provide an air-tight seal for the valve assembly, over time it may wear out and begin to crack eventually requiring a replacement. Please note this durable rubber seal is sold individually.

This is a Genuine OEM replacement part for use with Senco Nailers/Staplers. This item is made out of Rubber Material and it is Sold Individually. The purpose of this part is to create a seal so air does not leak from the gun. When replacing this Seal it is advised to inspect all of the other Seals and O-Rings for wear. When replacing this item you would need an Allen Wrench Set and Pliers.

This is an authentic replacement part manufactured for use with Senco pneumatic nailers and staplers. The special spring is commonly used to provide resistance for the single sequential type of trigger assembly. This spring is available as an individual replacement part.

This spring is an OEM part direct from Senco. The metal spring is compatible with several nailer devices, and is sold individually. This component provides the necessary resistance in the trigger. Pliers and a hex key are often required for the installation.

This authentic item is sourced directly from the original equipment manufacturer for use with Senco framing nailers. It is one of the special pins utilized to secure the cover for the trigger. The pin fits into the housing and is secured in place by a retainer which is sold separately. It provides a high-quality replacement for a missing ...Read moreor a damaged component that was installed on a new unit. To ensure the correct installation, refer to the appropriate diagram of your model. You will need pliers to remove and secure this hardware. NOte, one durable metal pin is included.

This is an Authentic OEM replacement part for use with Senco Nailers/Staplers. This item is made out of Rubber and it is Sold Individually. The purpose of this part is to create a seal so air does not leak from the gun. When replacing this Seal it is advised to inspect all of the other Seals and O-Rings for wear. When replacing this item you would need an Allen Wrench Set and Pliers.

This is an original replacement part sourced directly from the manufacturer. The seal is commonly found in Senco nailers. This part is made of flexible rubber, and is generally used to cushion and seal the connection between the main body and the guide body. You may require an Allen wrench or hex key when replacing this item. The seal is sold as an individual replacement part.

This replacement seal O-ring helps maintain an airtight seal within pneumatic nailers and staplers, ensuring consistent air pressure and reliable tool performance. Manufactured from durable rubber, it is designed to prevent air leaks within the tool's internal air system, helping restore proper driving power and operating efficiency when ...Read morethe original O-ring becomes worn, cracked, flattened, or damaged. Common symptoms of a failed seal include reduced fastening power, air leakage from the tool body, and inconsistent operation. Installation typically involves disassembling the affected portion of the tool, removing the worn O-ring, lightly lubricating the new seal with pneumatic tool oil, and installing it in the original groove before reassembly. Weighing approximately 0.01 lbs, this small but essential maintenance component helps extend tool life and maintain dependable performance. For best results, inspect related O-rings, seals, and cylinder components during servicing and replace any worn parts as needed to ensure a complete and long-lasting repair.

This is a genuine item that is supplied directly from the original equipment manufacturer for use with Senco nailers. It is an identical replacement for a missing or damaged cage that was originally installed on a new unit, please make sure to check the appropriate diagrams of your model for the correct location and application of this co...Read moremponent. Keep in mind this high-quality item is made of durable material and is sold individually.

This is an authentic replacement part manufactured for Senco pneumatic fasteners. The plastic trigger is used to actuate the trigger valve assembly when firing the fasteners. This trigger is available as an individual replacement part, please see model diagram for associative parts.