SKU3310605 MTD Lawn Tractor - Overview

This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into place. If it has signs of deformation or wear, you will need to replace it. To unthread this bolt, you need an adjustable wrench to loosen the ...Read morenut found on the end of the bolt. You may need to apply a lubricating oil to the bolt if it is stuck. You may need to clamp down on the head of the bolt with pliers while continuing to turn the nut counterclockwise. You can then slide the carriage bolt out of its hole or tap it gently with a hammer. This bolt is a standalone product and the nut is not included. This bolt was sourced directly from its manufacturer.

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

This OEM-manufactured flange bearing supports and enables the smooth rotation of parts in your lawn equipment, such as the blade assembly, axle assembly, or steering components. This bearing has an inner diameter of .76 inches, an outer diameter of .941 inches, and a width of 1 inch. It is made of plastic. A similar similar style flange b...Read moreearing can be used at the bottom of the crank, but it would be made of metal. When the bearing is broken, you may notice signs of wear and abnormal squealing noises coming from your machine. If neglected, the parts the bearing is supporting can overheat and potentially seize up. To switch out a flange bearing, you need to take off any bolts, screws, or clips that are holding it in place. Using a hammer or a bearing puller tool, gently push the bearing out of its housing. Since this part is sold individually, remember to refer to your user manual to understand how many bearings your machine will need. It is strongly recommended that you replace all the bearings in one go, as they wear out at the same rate.

The Lock Ball Joint Assembly is part of the steering mechanism, and the machine will not be able to steer without it. This part attaches to the steering block and drag link. Installation is rated as "Easy" and requires a wrench set and socket set.

When the brakes are applied, this brake puck presses against the brake disc in your lawn equipment to help slow down or stop it. The brake puck is in the brake assembly, which might be located near the transmission or the wheels of your machine. If you notice that the machine takes longer to stop or that there is a loud scraping or grindi...Read moreng noise when you push down on the brake, your brake puck may have worn out. If it is not replaced, you risk losing braking power, which leads to equipment damage or accidents. Before any repairs, make sure that your machine is turned off and that the spark plug is disconnected. To dissemble the brake assembly and access the brake puck, use pliers or a wrench to remove any bolts or clips holding it in place. With a screwdriver, pry the brake puck out of your machine. Since this genuine OEM part is sold individually, determine the number of pucks your machine needs by consulting your user manual.

This starter solenoid is designed to reliably engage the starter motor by allowing a low-power ignition signal to trigger the high-current starting circuit. Built for dependable performance, it helps resolve no-start or intermittent starting issues caused by a failed relay. Ideal for replacing a worn or faulty solenoid, it restores consis...Read moretent starting and reliable operation in lawn mowers, tractors, and snow-clearing equipment.

This replacement belt is sourced directly from original equipment manufacturer. It is a genuine OEM sourced item commonly used on lawn mowers and tractors. This is the the belt that drives the mower blades. Belts should be inspected periodically and be replaced if they are worn or stretched. Please note, this durable rubber belt is sold individually. To complete this repair you will need a set of wrenches.

This is a genuine replacement part produced by original manufacturer. It is used in various tractors from MTD, Yard Machines, Bolens, and Yard Man. Flange bearings facilitate spinning axles/shafts and reduce friction. They are a very high wear item that may require replacement often. Sold individually.

The air valve attaches to the wheel and is made of a durable material. This is a genuine MTD, Ryobi, Yard Machines, Bolens, Troy-Bilt, and Yard Man part sourced directly from the manufacturer for use in chippers, shredders, cultivators, edgers, lawn tractors, snowblowers, and trimmers. Keep in mind that this part is sold individually. Whe...Read moren replacing this item a set of pliers might be required during the installation process. It might wear out over time and will need replacing.

This flat idler pulley is designed to help maintain proper belt tension while reducing vibration and uneven wear in lawn and snow equipment drive systems. Made from durable metal for long-lasting performance, it supports smooth belt routing and consistent operation under regular use. Ideal for replacing a worn or noisy pulley, it helps restore reliable belt engagement and overall machine performance.