Models
>
SC8640EDQ1
SC8640EDQ1 Whirlpool Cooktop - Overview
Sections of the SC8640EDQ1
[Viewing 2 of 2]Keep searches simple, eg. "belt" or "pump".
Spark Electrode
PartSelect #: PS11740866
Manufacturer #: WP3185804
This part helps your burner ignite and produce flame.
$49.02
In Stock
Spark Module
PartSelect #: PS11748331
Manufacturer #: WPW10110491
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
$124.94
In Stock
Control Knob
PartSelect #: PS11740876
Manufacturer #: WP3187767
Sold individually. This knob accepts a D-shaped shaft.
$10.77
In Stock
Surface Burner Knob
PartSelect #: PS11731666
Manufacturer #: W10861812
Sold individually.
$22.55
Special Order
Gas Valve/Switch Seal Cover
PartSelect #: PS11740880
Manufacturer #: WP3188425
Part is located on top of the igniter switch that's next to the gas valve. Helps regulate gas flow and the amount of normal leakage that may occur.
$35.28
In Stock
Valve Screw
PartSelect #: PS3651486
Manufacturer #: W10491986
Part might differ in appearance, but functions same as original. Sold individually.
No Longer Available
Pressure Regulator
PartSelect #: PS11742618
Manufacturer #: WP4454571
This valve will automatically cut off the flow of gas when it reaches a certain pressure.
No Longer Available
Zip Tie
PartSelect #: PS11753208
Manufacturer #: WPW10339879
A zip tie, also known as a cable tie or a wire tie, is a fastening device that holds wires or tubing together. If a machine has wires or tubing that are easily shifted, you need to hold them tightly t...
$8.04
In Stock
Questions And Answers for SC8640EDQ1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the SC8640EDQ1
[Viewing 3 of 3]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
There was a crack in the porcelain not letting it spark
I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire.
Then just connected the new electrode and place the assy, in the burner.
Then just connected the new electrode and place the assy, in the burner.
Parts Used:
-
Billy from Martinsville, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
22 of 35 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top burners would not light. No "clicking" .
My husband and I replaced the igniter module, following directions we found online. We removed the old one, replaced it with the new one, and thankfully everything is working great!
Parts Used:
-
Carolyn from Bellingham, MA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
21 of 33 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken ignitor insulation; repeated sparking after burner lit
Disconnected gas & electric connections; lifted unit out of countertop onto padded table upside down. Unscrewed ~16 sheet metal screws for access. Removed bad ignitor by driving off retaining clip. Had to remove burner (3 screws) for access to install retaining clip on new ignitor. Reassembled, reinstalled. Works like new!
Parts Used:
-
Joe from San Bruno, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
15 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!