S252 Craftsman - Overview

The OEM bearing, also known as the flange bearing, is silver, made of metal, and sold individually. It is used on riding mowers to secure the wheel in place and allow it to rotate freely on the shaft. Over time, the part may become worn and damaged, which you will notice if you experience a squealing or grinding sound from the wheel in qu...Read moreestion, or you notice the wheel is sloppy on the shaft. You will need a hammer and punch to complete this repair, which most of our customers rated as easy. Make sure you tap the new bearing into place evenly inside the tire rim.

The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle. This part is black, made of metal, and around an inch in length. It is sold individually and may become damaged over time due to wear and fatigue.

This OEM washer, also known as a flat washer, has dimensions of 25/32 x 1-1/4. Silver in color and metal, the washer is sold individually. Although this part can have a range of applications depending on the equipment, its general function is to spread the load under a bolt. Ensure you consult your owners manual or check your model number...Read more to confirm this is the washer you need for your equipment. This part will need to be replaced when your existing one is worn or damaged. It is an easy repair according to our customers, and does not require any special tools.

This is an OEM replacement recoil kit supplied directly by Poulan. The starter pulley spins the flywheel to start the engine when you pull the starter rope. The most common reason for replacing the starter pulley is if the starter rope won't retract. Please note this kit does NOT include the rope and rewind spring. When replacing this part make sure to disconnect the spark plug wire before starting repair.

The Push Nut is a black, metal nut, which can be installed with pliers and a hammer. It's used to secure parts in place in various locations on a variety of equipment. If damaged will not longer hold in place. Installation is rated as "Easy", but it will depend on the parts your are securing and the equipment you are using. Consult your m...Read moreake, model and diagrams to ensure this is the correct part. The part is sold individually.

The screw with hex washer attaches to the pivot bracket assembly. This item is available as an individual replacement part. This genuine part is supplied by the original equipment manufacturer for use with Craftsman lawn tractors and lawn mowers. A wrench will be necessary during the installation of this item. It is made of metal and will require replacing if it becomes broken or stripped.

This lightbulb is supplied by the original manufacturer and intended for use in lawn tractors and riding mowers with a 12-volt system. It is positioned on the front of the equipment as part of the equipment lighting system. The lightbulb illuminates the area allowing for improved visibility when working in low-light conditions. The lightb...Read moreulb can fail due to various reasons, such as burnout, electrical issues, or physical damage. Once the lightbulb stops functioning, visibility will be reduced which makes it difficult to safely operate the equipment. Before you begin the repair, disconnect your equipment from the power source to avoid electrical hazards. Remove the bulb housing cover, and carefully unscrew the old bulb. Thread the new bulb into the housing and ensure that it is securely seated. Finally, reattach the housing cover, reconnect the power supply, and test the new bulb. Note that this bulb is part of a dual usage system, therefore ensure that you order at least two as each bulb is sold individually.

The oil drain valve connects to the easy oil tube drain and the oil pan and helps to drain the oil out of the engine. This part is made out of metal and is available individually. It will need to be replaced if it becomes broken and a set of pliers may be needed when replacing this part. This valve is an original part from Ryobi and Husqvarna for use in ride lawn mowers and lawn tractors.

It is a genuine OEM sourced replacement screw which is specially designed for use with Husqvarna, Poulan and Ryobi riding lawn mowers and garden tractors. This item is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for the correct location and use of ...Read morethis item. It is a high-quality hex head screw which is made of durable metal and it is sold individually.

This is a genuine replacement part manufactured for use with riding lawnmowers. This is the outer tire for the front wheels. The tire tread wears from normal use, it is recommended to replace worn tires. This tire is sold individually, the inner tube and other associative parts are available separately.

This is an authentic replacement part manufactured for use with lawn and garden equipment. This valve stem is used with equipment that has inflatable tires. The valve is a one-way valve allowing air into the tire while not letting air escape the valve. This valve stem is sold as an individual replacement part, please see model diagram for associative parts and compatibility.