S166B-C Jenn-Air Wall Oven - Instructions

Regrettably I have been unable to replace the bake element since the two screws are completely stuck. This doesn't appear to be a common problem.

Bought a pair for needed door hinges for replacement. Found a DIY video on You Tube showing technique to replace. Door removal was a bit awkward but hinge replacement and door reinstallation was as detailed in video. Could not nor would not have tackled this project without video. Premium quality parts sent and received within days of ordering. Wife happy therefore so am I.

Shut off electrical breaker to stove. Unscrew & remove heating element with standard screwdriver. Since screw threads were stripped I used a longer screw I wrapped thread with teflon tape. Connect new heating element & crimp connectors to ensure contact is made, push wires back & tighten screws. Turn power breaker back on & we have a new oven!

I removed the back of the stove for easy access to the wiring (three hex head screws) and removed the two wire leads. Then I began to remove the mounting screws from the inside of the oven, the first three screws came out fine the last one was so tight that I had to resort to vise grip pliers. Jenn-Air should have used hex head screws instead of phillips head inside the oven. Finally after about 15 minutes the last screw came out. I installed the new element, reinstalled the screws and wires. Then I replaced the back and tested. Total about 45 minutes.

Received the new one. Installed it in 15 minutes. Thanks for the fast service.I will buy from you guys the next time I need a part ! Thank You, Henry

plugged new one in

My husband and I couldn't believe we were able to do this!!!So easy! We were dancing around the kitchen!!!!! We credit the advice of other do-it-yourselfers. Very accurate and true. It took less than 10 minutes after the screws were WD40'd. In addition, we recommend: use a flashlight to see in the oven since it's dark with the power cut off , and use this time to clean behind the stove!!!!!

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

The door came off easily after I removed the two hinge covers that are attached to the oven. Taking the door off can be done with one person but ideally two.

The new parts fit in perfectly and the hinge pin used for shipping comes out easiest with a pair or wire cutters (you do not cut it just grab it and pull).

After that, re-assemble the door and drop in place. It was a snap.

FYI...the shipping was ultra fast and the price was great.

No issues whatsover with the entire process.

takes two people to put the oven door back in place but otherwise very simple as long as you keep all your screws and pads in place

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

It was easy. Just remove the two screws, gently pull the housing out, remove the two wiring clips, and then reverse the process with the replacement.

It was difficult to take out the burned out part, because it was in for so long, but WD 40 helped take it out. First I unscrewed the two screws, then pulled the element out enough, so I could disconnect the wires. finelly I took the element out, put in the new one and did the same thing backwards, i.e. attached the wires, screwed in the two screws, then I tested it, and when I saw it worked, it was done.

This repair was so eazy my 18 old son repaired it.

Removed old element by removing screws from plate and removing old wires. Had to get conversion from electric store as new element was screw in and the old one was hard wired. Stripped old wires and placed on converters. Screwed the electric converter parts to the element. Screwed into oven wall.