RY802925 (095079510) Ryobi Pressure Washer - Overview

This detergent suction kit, also known as a soap or chemical injection kit, is designed for use with a pressure washer. This is a genuine OEM part designed to inject soap into the water stream of your pressure washer, and includes the main injector valve, two differently sized O-rings, a spring, and a ball bearing. One end of this kit wil...Read morel be threaded into the washer, and the other will lead to your cleaner with a siphon, which is sold separately. This injection kit would need to be replaced if the nozzle is leaking, the injector fails to work properly, or water is getting into the soap dispenser. To replace, simply unscrew the previous injector and remove it, then fit the small O-ring inside the threaded end of the new injector, along with the ball bearing and then spring. Wrap the larger O-ring around the base of the threaded end, and apply a layer of lubricant, before installing the new injector and securing it.

This OEM outlet tube, also known as a hose connector, allows pressurized water to flow from the pump of your pressure washer to the nozzle. Connecting the hose to the handle assembly and the spray wand, it is where the water exits from your machine so you can direct the stream towards a desired surface. You can tell if an outlet tube is b...Read moreroken when it has visible cracks or holes and when water leaks or sprays from the connection points or along the tube. A damaged or blocked tube can result in a loss of pressure and potentially premature wear or machine failure. To remove the outlet tube, use a wrench set to unscrew it from the pump. Please note that this replacement part is sold separately from the pump assembly.

This is an original replacement part designed for the Homelite and Ryobi pressure washers listed below. This is a low pressure nozzle which draws soap/chemical mixture from the detergent tank, and gently spray a light coat onto a surface for cleaning. This soap nozzle may also be called a chemical injector tip. One (1) nozzle is included.

The collar attaches to the spindle. This item is made out of plastic and metal and is sold individually. This is an authentic part from Ryobi and Homelite for use in pressure washers. An allen wrench might be necessary during the installation of this part. It will require replacing if it becomes broken.

It is a genuine OEM item that is made for use with Homelite and Ryobi and Homelite pressure washers. This is a special component which helps to provide a tight fit between connected components. Over time it may wear out or get damaged eventually requiring a replacement. Make sure to check the appropriate diagrams for your model to ensure ...Read morethe proper repair procedure. It is made of durable metal and is sold individually. A wrench might be needed to replace this inlet filter connector.

This is an original part from Homelite. The lock nut (m8 x 1-1/4 mm) is compatible with many pressure washers, and is sold individually. The metal lock nut helps to secure various components of the pressure washer. A wrench, hex key and screwdriver are often needed for the installation.

It is a genuine replacement part that is supplied by original equipment manufacturer for use with Homelite, Ridgid and Ryobi pressure washers. This siphon tube is used to deliver the chemical solution from the tank to the pump. Over time the tube may develop cracks allowing for leaks, if this happens this part can easily be replaced. It is made of durable flexible rubber material and it is sold individually.

This is an authentic Ryobi replacement part that has been sourced from the original manufacturer to be used with circular saws. The two wire cord is encased in a durable casing and is used to relay electricity from the outlet to the switch assembly. This cord is available as an individual replacement part.

This is a genuine replacement part that has been OEM sourced to be used with pressure washers from Homelite, Ryobi, and Ridgid. The special filter connects to the end of the chemical siphon tube and is used to prevent dirt from entering the pump. This item is available as an individual replacement part.

This manufacturer-approved nut is supplied by the original manufacturer for use with Homelite, Ryobi and Ridgid pressure washers. It is a standard hardware which may have multiple applications. Make sure to refer to the appropriate diagrams for your model to ensure the exact location and the correct application of this part. This high-qua...Read morelity nut is made of durable metal and is sold individually. A wrench will be needed to secure or remove it.