RY52004A Ryobi Pole Saw - Overview

The OEM Air Filter is used to stop debris and particles from entering the carburetor and engine, which could cause damage. It is attached in the air filter housing. It comes in black, and is contructed from foam. Installation is rated as "Easy" by customers, and will require a screwdriver. (Tip: You can place the filter in a plastic bag w...Read moreith a bit of oil, remove it, and then squeeze the filter to drain the excess oil. The remaining oil will work as a sticky trap). If the part becomes worn over time, the engine will be hard to start and will run rich. In this case, replace the part. Refer to your make, model and diagram to ensure this is the correct part for you.

Genuine OEM replacement part, this item is sold individually. This part is used to cover the Gear Case & Cover Assembly. It has two holes at the top, one for part of the Gear Case and another for the Oil Cap With Retainer. This part contains the oil needed for the Gear Case to keep it lubricated. It is secured to the Gear Case by four screws, part number 985895001.

This genuine OEM guide bar supports the cutting chain on your handheld lawn equipment. It extends from the main body of your machine, holding the chain securely. It is 12 inches long but designed for a maximum cutting length of 10 inches. To determine if a guide bar is broken or damaged, look for visible cracks, bends, or excessive wear. ...Read moreCheck if the guide bar is misaligned or feels loose when attached to the chainsaw. A broken guide bar can cause binding, difficulty cutting, or excessive vibration. Not replacing a damaged guide bar can lead to safety risks, reduced performance, and increased wear. To replace a guide bar, you will need a screwdriver and a wrench. Start by loosening the tension on the blade. Next, remove the bar clamp assembly and lift the blade out of the old bar, taking care to free it from around the sprocket. Finally, remove the old bar. Please note that this guide bar is sold separately from the cutting chain.

This is a genuine OEM replacement part, sold individually. This Bumper helps keep the fuel tank in place, and minimizes vibration of the fuel tank. This part is used with a variety of string trimmers, compatible with the models listed below.

This crankcase cover gasket seals the crankcase cover of your lawn equipment engine, preventing air or fuel leaks and maintaining proper internal pressure. It is sized at 2 1/2 inches by 2 1/2 inches and is commonly found where the crankcase cover attaches to the engine block. You can tell if a crankcase cover gasket is broken if there is...Read more oil around the edges of the cover. Your machine may also experience a loss of power or unusual noise. If the gasket is not replaced, your machine may have fuel leaks or decreased performance. Debris and contaminants will also enter the engine, reducing the lifespan of your machine. When replacing the gasket, use a wrench or socket to unthread any bolts securing the crankcase cover. You will then be able to take the gasket off your machine. Bear in mind that this OEM gasket is sold individually.

Genuine OEM replacement part, this item is sold individually. This Clutch Drum is used on all of the outdoor products shown below. It contains the screw to attach this part to the spindle of the engine. It is usually a Torx T-25 Screw or a T-20. Once the engine gets to a certain RPM the clutch will expand and come in contact with the inside of the clutch drum. This will start the rotation of the Trimmer drive shafts.

This is an OEM replacement part,it is sold individually. The purpose of the Air Purge Bulb is to purge all of the air from the carburetor. It then brings fuel up through the fuel line in the tank into the carburetor. Once the carburetor is full of fuel the Bulb will force the excess fuel back into the tank through the fuel return line. ...Read moreOver time the bulb will loose it elasticity or begin to crack, it will need to be replaced at this time.

It is a genuine OEM approved component that is specially made for use with handheld lawn and garden equipment. The purpose of this clip is to secure the fuel line, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Unfortunately, over time parts may wear out, get ...Read moredamaged or simply lost eventually requiring a replacement. Please note this high-quality clip is made of durable metal and is sold individually.

This is an authentic OEM sourced component which is specially designed for Ryobi, Homelite and Toro lawn and garden equipment. It is an identical replacement for a missing or a faulty clip that was originally installed on a new unit, please make sure to check the appropriate diagrams of your model for the correct location and application ...Read moreof this hardware. Keep in mind this high-quality item is made of durable metal and is sold individually.

This hanger cap, also known as a mounting clip, is a genuine replacement part from the equipment manufacturer to help you store hand attachments that you are using. It is a small plastic cap that acts as a protective cover for the hanger hook in lawn and garden equipment. It protects the hook from damage and keeps it from getting caught o...Read moren other items. You will need one cap for each of the attachments or tools you have. The cap will need to be replaced if it is damaged or can no longer stay attached to the equipment. To install the new cap, simply place the new cap at the end of the attachment on your equipment. Sold individually.