RY52002 (PC30) Ryobi Pole Saw - Overview

This spool retainer is sourced from the equipment manufacturer for use in trimmers. It is a plastic knob, measuring 2 inches in diameter, with a threaded metal bolt in the center. The retainer has a right hand thread, and it is used to secure the spool within the trimmer head to prevent it from coming loose during operation. The retainer ...Read moreengages with the trimmer head to lock the spool in place, while it also advances the cutting line for greater cutting efficiency. If the threads on the retainer bolt wear out or the plastic body becomes damaged, the retainer will be unable to engage with the trimmer head, causing the line to tangle, the spool to come loose, and lowering the cutting performance of the trimmer. Remove the trimmer head cover and detach the retainer from the assembly. Position the new spool retainer in the assembly and thread it firmly into place.

The OEM Air Filter is used to stop debris and particles from entering the carburetor and engine, which could cause damage. It is attached in the air filter housing. It comes in black, and is contructed from foam. Installation is rated as "Easy" by customers, and will require a screwdriver. (Tip: You can place the filter in a plastic bag w...Read moreith a bit of oil, remove it, and then squeeze the filter to drain the excess oil. The remaining oil will work as a sticky trap). If the part becomes worn over time, the engine will be hard to start and will run rich. In this case, replace the part. Refer to your make, model and diagram to ensure this is the correct part for you.

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This genuine OEM guide bar supports the cutting chain on your handheld lawn equipment. It extends from the main body of your machine, holding the chain securely. It is 12 inches long but designed for a maximum cutting length of 10 inches. To determine if a guide bar is broken or damaged, look for visible cracks, bends, or excessive wear. ...Read moreCheck if the guide bar is misaligned or feels loose when attached to the chainsaw. A broken guide bar can cause binding, difficulty cutting, or excessive vibration. Not replacing a damaged guide bar can lead to safety risks, reduced performance, and increased wear. To replace a guide bar, you will need a screwdriver and a wrench. Start by loosening the tension on the blade. Next, remove the bar clamp assembly and lift the blade out of the old bar, taking care to free it from around the sprocket. Finally, remove the old bar. Please note that this guide bar is sold separately from the cutting chain.

This is a genuine OEM replacement part, sold individually. This Bumper helps keep the fuel tank in place, and minimizes vibration of the fuel tank. This part is used with a variety of string trimmers, compatible with the models listed below.

Springs are used within outdoor power equipment to provide tension and shock absorption, depending on their application and use. This spring is designed for use within trimmers/brush cutters and is made to provide tension on the spool reel mechanism, and in some cases may be used to advance the line whenever portions of it are cut off. Th...Read moreis spring measures approximately 1.3-inches in length when extended and comes as an individual part. If you notice the line/spool in your trimmer is not advancing or is coming too quickly, the spring may be damaged and need replacing. Since this spring is a high-use part, it is not uncommon for it to lose tension over time and need to be replaced. To replace the spring, you will need to unscrew the covering cap, remove the spool feeding reel, remove the old spring and install the new spring with the rest of the assembly. Make sure to feed the line back into the appropriate feeding holes prior to operation of the trimmer.

Genuine OEM replacement part, this item is sold individually. This Clutch Drum is used on all of the outdoor products shown below. It contains the screw to attach this part to the spindle of the engine. It is usually a Torx T-25 Screw or a T-20. Once the engine gets to a certain RPM the clutch will expand and come in contact with the inside of the clutch drum. This will start the rotation of the Trimmer drive shafts.

It is a genuine OEM approved component that is specially made for use with handheld lawn and garden equipment. The purpose of this clip is to secure the fuel line, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Unfortunately, over time parts may wear out, get ...Read moredamaged or simply lost eventually requiring a replacement. Please note this high-quality clip is made of durable metal and is sold individually.

This item has been OEM sourced and is intended to be used with gas-powered trimmers and pruners from Ryobi & Homelite. The gasket is used to seal the connection between the cylinder and the crankcase. It is recommended to replace gaskets when servicing the motor to ensure proper seals and spacing when the parts are reassembled. This item is priced as a single part.

This is an authentic OEM sourced component which is specially designed for Ryobi, Homelite and Toro lawn and garden equipment. It is an identical replacement for a missing or a faulty clip that was originally installed on a new unit, please make sure to check the appropriate diagrams of your model for the correct location and application ...Read moreof this hardware. Keep in mind this high-quality item is made of durable metal and is sold individually.