RY30060 (BC30) Ryobi Brush Cutter - Overview

The OEM Air Filter is used to stop debris and particles from entering the carburetor and engine, which could cause damage. It is attached in the air filter housing. It comes in black, and is contructed from foam. Installation is rated as "Easy" by customers, and will require a screwdriver. (Tip: You can place the filter in a plastic bag w...Read moreith a bit of oil, remove it, and then squeeze the filter to drain the excess oil. The remaining oil will work as a sticky trap). If the part becomes worn over time, the engine will be hard to start and will run rich. In this case, replace the part. Refer to your make, model and diagram to ensure this is the correct part for you.

This flanged star washer is a manufacturer-sourced replacement part designed for use trimmers. It is also known as a tooth lock washer due to its serrated inner edge which resembles inward facing teeth. These teeth bite into the head of the fastener and provide a better grip than standard washers. This washer also has a flange on one side...Read more which is a lip that extends past the edge of the washer. It helps to distribute the load of the fastener over a wider area to provide extra stability and a more secure hold. Over time the washer may wear down or become damaged. To remove the washer, first unthread the bolt/screw it is fastened on. Use pliers to grip the washer and gently twist it off. Place the new washer over the fastener with the teeth facing toward the surface being fastened and insert it into the designated hole. Ensure that it is locked into place. Each washer is sold individually.

Springs are used within outdoor power equipment to provide tension and shock absorption, depending on their application and use. This spring is designed for use within trimmers/brush cutters and is made to provide tension on the spool reel mechanism, and in some cases may be used to advance the line whenever portions of it are cut off. Th...Read moreis spring measures approximately 1.3-inches in length when extended and comes as an individual part. If you notice the line/spool in your trimmer is not advancing or is coming too quickly, the spring may be damaged and need replacing. Since this spring is a high-use part, it is not uncommon for it to lose tension over time and need to be replaced. To replace the spring, you will need to unscrew the covering cap, remove the spool feeding reel, remove the old spring and install the new spring with the rest of the assembly. Make sure to feed the line back into the appropriate feeding holes prior to operation of the trimmer.

This is a genuine item that is supplied by the original equipment manufacturer for Ryobi, Toro and Homelite handheld lawn and garden equipment. It is an identical replacement for a missing or damaged string guard clamp that was originally installed on a new unit, please make sure to refer to the owners manual of your model for the correct...Read more application of this component. Keep in mind this high-quality part is made of durable metal and is sold individually.

This is a genuine OEM supplied replacement gearbox assembly that is specially designed for Ryobi and Homelite handheld lawn and garden equipment. It is attached to the lower boom assembly and it is what drives the trimmer head. Over time the internal components such as gears may wear out and begin to fail eventually requiring a replacement. It is made from durable metal and it is sold individually.

This is a Manufacturer Sourced replacement part for Lawn and Garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt. This Locking Nut secures the cutting blade on the Trimmers/Brushcutters. You would need a Wrench to tighten or loosen this Hex Nut.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Homelite and Ryobi handheld lawn and garden equipment. This is the special screw which is utilized to secure the gear head, please refer to the appropriate diagrams of your model for the correct location and application of this hardware. K...Read moreeep in mind this durable metal hex head screw is sold individually, you will need a wrench to secure or remove it.

Ergo grip starter handle

The cupped washer attaches to the tri-arc blade with the use of the lock nut. This part is an OEM from Ryobi and Homelite to be used in brushcutters and trimmers. It is made of metal and helps to keep the cutting tool in place. A wrench will be needed if this part needs to be replaced. This washer is priced as an individual replacement part.

This is a genuine OEM replacement strap made for various yard tools. This fabric strap features one metal lobster clasp, which attaches to the tool via the strap hanger. It is adjustable with a plastic slide adjuster. One strap is included.

It is an authentic component that is supplied by the original equipment manufacturer for use with Homelite and Ryobi handheld string trimmers. This is an identical replacement for a missing or a faulty handle bar clamp that was installed on a new unit. The part is utilized to secure the handle bar. Please make sure to refer to the appropr...Read moreiate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality clamp is made of durable metal and is sold individually.