RY28140SS26 Ryobi Trimmer - Overview

This is an OEM Manufacturer Sourced replacement part used on certain Gas Powered String Trimmers. This part is made out of Foam and it is Sold Individually. Its purpose is to filter out dust and debris from contaminating the carburetor and engine. When replacing the filter you can open the package in comes in and put a bit of two cycle oi...Read morel in the bag and let it absorb into the filter. Then remove it from the bag and squeeze it with a paper towel to remove the excess oil. This will aid the filter in filtering out the unwanted debris.

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

Springs are used within outdoor power equipment to provide tension and shock absorption, depending on their application and use. This spring is designed for use within trimmers/brush cutters and is made to provide tension on the spool reel mechanism, and in some cases may be used to advance the line whenever portions of it are cut off. Th...Read moreis spring measures approximately 1.3-inches in length when extended and comes as an individual part. If you notice the line/spool in your trimmer is not advancing or is coming too quickly, the spring may be damaged and need replacing. Since this spring is a high-use part, it is not uncommon for it to lose tension over time and need to be replaced. To replace the spring, you will need to unscrew the covering cap, remove the spool feeding reel, remove the old spring and install the new spring with the rest of the assembly. Make sure to feed the line back into the appropriate feeding holes prior to operation of the trimmer.

This carburetor gasket is an OEM replacement part for use in a variety of lawn and garden outdoor equipment. It seals the area between the carburetor and the intake manifold to prevent air and fuel from leaking. Over time, the gasket may wear down, crack, or warp due to normal aging, exposure to heat and chemicals, or improper installatio...Read moren. A faulty gasket will cause air and fuel to leak, resulting in hard starting, rough idling, fuel wastage, and overall lower engine performance. To replace the gasket, remove the air filter cover, air filter, and carburetor. Carefully pull off the old gasket, and thoroughly clean the sealing surface of all residues. Place the new carburetor gasket onto the intake manifold, and firmly press it in place. Reassemble the equipment parts in reverse order to complete your repair.

This spring is a genuine OEM replacement part supplied directly from the manufacturer. It is designed for use in various models of Ryobi string trimmers. This coil type compression spring is placed inside the string head housing. It is made of metal and sold individually.

This fuel filter is a genuine OEM part that is compatible with various lawn equipment models and is sold as an individual part. Fuel filters are used to remove dirt and debris from fuel entering the carburetor and engine and are made of metal with a fabric filter material, meaning this filter will eventually clog and need to be replaced. ...Read morePlease note that the fuel filter should be inspected regularly, not solely when it is clogged. The filter will be attached to the fuel line within the fuel tank and if your equipment is having starting, revving, or idling issues, the fuel filter may be the reason why. To replace it, simply use a hook to pull the old filter out from the fuel tank, use pliers to remove any clamps attached to the end of the fuel line, and pull the filter off. Attach the new filter to the fuel line, along with the clamp, and set the filter back into the tank.

This Gear gear head assembly is designed to transfer power from the drive shaft to the cutting head, allowing the string trimmer or brush cutter to operate smoothly and efficiently. Housed in a durable gearcase, it supports reliable rotation and helps maintain consistent cutting performance during use. Replacing a worn or damaged gear hea...Read mored can resolve issues such as loss of power to the cutting head, excessive noise, or erratic operation, restoring dependable performance. A properly functioning gear head also helps reduce strain on the drive system, contributing to longer service life and more efficient trimming results.

This is an OEM sourced replacement part used on gas trimmers. A centrifugal clutch is a part that uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driven shaft. Today's centrifugal clutches will function even when they shouldn't, far beyond the point of when they need to be replaced. Keepin...Read moreg an eye on equipment performance will determine when the centrifugal clutch requires attention. Please note the clutch drum, spacer and washer are all sold separately. This clutch is made out of metal and it is sold individually. To replace this item you would need a screwdriver and pliers.

This is a genuine OEM sourced replacement part which is specially designed for use with Ryobi handheld lawn and garden equipment. The ignition module also known as armature-magneto provides the current for the ignition system by producing pulses of high voltage for the spark plugs. Unfortunately, over time components will wear out and the...Read morey may begin to fail eventually requiring a replacement. Keep in mind it is made of high-quality metal with a rubber insulated spark plug boot and is sold individually.

This component is supplied by the original equipment manufacturer for use with Ryobi and Homelite handheld string trimmers. It is a high-quality replacement for a damaged or a missing easy starter assembly that was installed on a new unit. This is an important component of the pull-starter mechanism that allows a user to start the engine....Read more Refer to the appropriate diagrams of your model for the correct installation of the new assembly. Keep in mind this part is made of durable plastic material and is sold individually. You will need a screwdriver to perform this repair.

This replacement wing screw is a genuine OEM sourced item, it is not an aftermarket imitation. It is specially designed for Homelite and Ryobi string trimmers and brush cutters. This hardware is generally used to secure the grass deflector. This screw is made from durable metal and it is sold individually.

This is an OEM replacement part. It has a left hand threaded screw to remove and attach it to the trimmer head. Its purpose is to hold the spool with the cutting line, in the spool housing. It also acts as the bumper to advance the line from the spool. This is a well used and abused part of the trimmer. It may be a good idea to order an extra one.