RY28065 Ryobi Brush Cutter - Overview

This authentic OEM starter rope measures 42-inches and is for use with various models of outdoor power equipment. Made of nylon, this rope wraps around the starter recoil spring and when pulled, is used to start the engine. This rope is sold as an individual part, so any necessary grips are sold separately.

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This is a genuine Ruixing replacement part, it is sold individually. By pressing the bulb, it will purge the carburetor of air. Fuel will be forced up from the fuel tank through the fuel line then into the carburetor. Then the excess fuel will be forced back into the fuel tank through the fuel return line. At some time the primer will l...Read moreose its elasticity or crack and need to be replaced. We have an article and video on How to Replace a Primer Bulb, in our Repair Center. That can be found on the front page of our site.

This flanged star washer is a manufacturer-sourced replacement part designed for use trimmers. It is also known as a tooth lock washer due to its serrated inner edge which resembles inward facing teeth. These teeth bite into the head of the fastener and provide a better grip than standard washers. This washer also has a flange on one side...Read more which is a lip that extends past the edge of the washer. It helps to distribute the load of the fastener over a wider area to provide extra stability and a more secure hold. Over time the washer may wear down or become damaged. To remove the washer, first unthread the bolt/screw it is fastened on. Use pliers to grip the washer and gently twist it off. Place the new washer over the fastener with the teeth facing toward the surface being fastened and insert it into the designated hole. Ensure that it is locked into place. Each washer is sold individually.

Springs are used within outdoor power equipment to provide tension and shock absorption, depending on their application and use. This spring is designed for use within trimmers/brush cutters and is made to provide tension on the spool reel mechanism, and in some cases may be used to advance the line whenever portions of it are cut off. Th...Read moreis spring measures approximately 1.3-inches in length when extended and comes as an individual part. If you notice the line/spool in your trimmer is not advancing or is coming too quickly, the spring may be damaged and need replacing. Since this spring is a high-use part, it is not uncommon for it to lose tension over time and need to be replaced. To replace the spring, you will need to unscrew the covering cap, remove the spool feeding reel, remove the old spring and install the new spring with the rest of the assembly. Make sure to feed the line back into the appropriate feeding holes prior to operation of the trimmer.

This carburetor gasket is an OEM replacement part for use in a variety of lawn and garden outdoor equipment. It seals the area between the carburetor and the intake manifold to prevent air and fuel from leaking. Over time, the gasket may wear down, crack, or warp due to normal aging, exposure to heat and chemicals, or improper installatio...Read moren. A faulty gasket will cause air and fuel to leak, resulting in hard starting, rough idling, fuel wastage, and overall lower engine performance. To replace the gasket, remove the air filter cover, air filter, and carburetor. Carefully pull off the old gasket, and thoroughly clean the sealing surface of all residues. Place the new carburetor gasket onto the intake manifold, and firmly press it in place. Reassemble the equipment parts in reverse order to complete your repair.

This carburetor is for line trimmers. Carburetor mixes air and gas before the fuel mix goes to the engine. Wear work gloves to protect your hands and work in a well-ventilated area during this repair.

This fuel filter is a genuine OEM part that is compatible with various lawn equipment models and is sold as an individual part. Fuel filters are used to remove dirt and debris from fuel entering the carburetor and engine and are made of metal with a fabric filter material, meaning this filter will eventually clog and need to be replaced. ...Read morePlease note that the fuel filter should be inspected regularly, not solely when it is clogged. The filter will be attached to the fuel line within the fuel tank and if your equipment is having starting, revving, or idling issues, the fuel filter may be the reason why. To replace it, simply use a hook to pull the old filter out from the fuel tank, use pliers to remove any clamps attached to the end of the fuel line, and pull the filter off. Attach the new filter to the fuel line, along with the clamp, and set the filter back into the tank.

This is a genuine manufacturer-sourced component that is specially designed for use with Ryobi, Ridgid and Homelite equipment. It is an identical replacement for a missing or faulty switch that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and applicati...Read moreon of this item. Keep in mind this high-quality plastic body switch is sold individually.

Genuine OEM replacement part, this item is sold individually. This part is installed in between the carburetor and the air box cover It is the Air Filter for the outdoor equipment listed below. It has a fine mesh material for the Air Filter. Once this filter gets dirty and or clogged it can be blown clean or brushed clean. If it develops...Read more a hole in it or gets torn, it should be replaced ASAP, or it could cause damage to the carburetor and engine.

This bolt helps to secure air filter and carburetor assemblies to the short block. It is sourced from original equipment manufacturer for use with string trimmers. Usually this bolt would need replacement if it is lost or has stripped threads or head socket. To install or remove this bolt a hex key/allen wrench would be needed.

This is an OEM sourced replacement part used on gas trimmers. A centrifugal clutch is a part that uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driven shaft. Today's centrifugal clutches will function even when they shouldn't, far beyond the point of when they need to be replaced. Keepin...Read moreg an eye on equipment performance will determine when the centrifugal clutch requires attention. Please note the clutch drum, spacer and washer are all sold separately. This clutch is made out of metal and it is sold individually. To replace this item you would need a screwdriver and pliers.