RY28040SS26 Ryobi Trimmer - Overview

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This is a genuine Ruixing replacement part, it is sold individually. By pressing the bulb, it will purge the carburetor of air. Fuel will be forced up from the fuel tank through the fuel line then into the carburetor. Then the excess fuel will be forced back into the fuel tank through the fuel return line. At some time the primer will l...Read moreose its elasticity or crack and need to be replaced. We have an article and video on How to Replace a Primer Bulb, in our Repair Center. That can be found on the front page of our site.

Springs are used within outdoor power equipment to provide tension and shock absorption, depending on their application and use. This spring is designed for use within trimmers/brush cutters and is made to provide tension on the spool reel mechanism, and in some cases may be used to advance the line whenever portions of it are cut off. Th...Read moreis spring measures approximately 1.3-inches in length when extended and comes as an individual part. If you notice the line/spool in your trimmer is not advancing or is coming too quickly, the spring may be damaged and need replacing. Since this spring is a high-use part, it is not uncommon for it to lose tension over time and need to be replaced. To replace the spring, you will need to unscrew the covering cap, remove the spool feeding reel, remove the old spring and install the new spring with the rest of the assembly. Make sure to feed the line back into the appropriate feeding holes prior to operation of the trimmer.

This carburetor gasket is an OEM replacement part for use in a variety of lawn and garden outdoor equipment. It seals the area between the carburetor and the intake manifold to prevent air and fuel from leaking. Over time, the gasket may wear down, crack, or warp due to normal aging, exposure to heat and chemicals, or improper installatio...Read moren. A faulty gasket will cause air and fuel to leak, resulting in hard starting, rough idling, fuel wastage, and overall lower engine performance. To replace the gasket, remove the air filter cover, air filter, and carburetor. Carefully pull off the old gasket, and thoroughly clean the sealing surface of all residues. Place the new carburetor gasket onto the intake manifold, and firmly press it in place. Reassemble the equipment parts in reverse order to complete your repair.

This Gear gear head assembly is designed to transfer power from the drive shaft to the cutting head, allowing the string trimmer or brush cutter to operate smoothly and efficiently. Housed in a durable gearcase, it supports reliable rotation and helps maintain consistent cutting performance during use. Replacing a worn or damaged gear hea...Read mored can resolve issues such as loss of power to the cutting head, excessive noise, or erratic operation, restoring dependable performance. A properly functioning gear head also helps reduce strain on the drive system, contributing to longer service life and more efficient trimming results.

This is an OEM sourced replacement part used on gas trimmers. A centrifugal clutch is a part that uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driven shaft. Today's centrifugal clutches will function even when they shouldn't, far beyond the point of when they need to be replaced. Keepin...Read moreg an eye on equipment performance will determine when the centrifugal clutch requires attention. Please note the clutch drum, spacer and washer are all sold separately. This clutch is made out of metal and it is sold individually. To replace this item you would need a screwdriver and pliers.

This is a genuine item that is supplied by the original equipment manufacturer for Ryobi, Toro and Homelite handheld lawn and garden equipment. It is an identical replacement for a missing or damaged string guard clamp that was originally installed on a new unit, please make sure to refer to the owners manual of your model for the correct...Read more application of this component. Keep in mind this high-quality part is made of durable metal and is sold individually.

This component is supplied by the original equipment manufacturer for use with Ryobi and Homelite handheld string trimmers. It is a high-quality replacement for a damaged or a missing easy starter assembly that was installed on a new unit. This is an important component of the pull-starter mechanism that allows a user to start the engine....Read more Refer to the appropriate diagrams of your model for the correct installation of the new assembly. Keep in mind this part is made of durable plastic material and is sold individually. You will need a screwdriver to perform this repair.

This replacement wing screw is a genuine OEM sourced item, it is not an aftermarket imitation. It is specially designed for Homelite and Ryobi string trimmers and brush cutters. This hardware is generally used to secure the grass deflector. This screw is made from durable metal and it is sold individually.

This is an OEM replacement part. It has a left hand threaded screw to remove and attach it to the trimmer head. Its purpose is to hold the spool with the cutting line, in the spool housing. It also acts as the bumper to advance the line from the spool. This is a well used and abused part of the trimmer. It may be a good idea to order an extra one.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Homelite and Ryobi handheld lawn and garden equipment. This is the special screw which is utilized to secure the gear head, please refer to the appropriate diagrams of your model for the correct location and application of this hardware. K...Read moreeep in mind this durable metal hex head screw is sold individually, you will need a wrench to secure or remove it.