RY25PHEMC (090333045) Ryobi Trimmer - Overview

This airbox cover, also known as an air filter cover, is an authentic manufacturer replacement cover for trimmers. It has one label on the front side which states the starting instructions for the trimmer. The airbox cover protects the air filter and ensures that the engine receives the correct amount of air for combustion. It also helps ...Read moreto prevent contaminants from entering the engine and damaging it. If the cover is damaged or improperly installed, the flow of air will be restricted resulting in poor combustion and decreased performance. Dirt and debris will also be able to enter the engine, leading to overheating and premature failure. To complete the repair, locate the air filter housing on your engine and remove the faulty cover. Inspect the air filter in case it is damaged or dirty as well. It is important to regularly check and replace the air filter as a part of your equipment maintenance. Clean the air filter housing and place the new cover in position.

This is a genuine item that is sourced directly from the parts manufacturer for use with a Ryobi string trimmer. The upper boom assembly connects the motor head to the lower boom assembly. This part is made if of a high-quality metal and is sold as an individual replacement part.

The OEM Air Filter is used to stop debris and particles from entering the carburetor and engine, which could cause damage. It is attached in the air filter housing. It comes in black, and is contructed from foam. Installation is rated as "Easy" by customers, and will require a screwdriver. (Tip: You can place the filter in a plastic bag w...Read moreith a bit of oil, remove it, and then squeeze the filter to drain the excess oil. The remaining oil will work as a sticky trap). If the part becomes worn over time, the engine will be hard to start and will run rich. In this case, replace the part. Refer to your make, model and diagram to ensure this is the correct part for you.

This OEM switch is used on a variety of different lawn equipment models and is sold individually. This switch is used to turn your lawn equipment on and off, so if your equipment is either not turning on, or this switch feels loose within its housing, it may be time to replace it. To remove it, separate the two halves of the housing which...Read more it connects to, disconnect the throttle and other wires with pliers, and depress the securing tabs. To install the new switch, click it into place within the housing and connect the appropriate wires to the two terminals, and then reconnect the throttle cable and other wires, and then simply align the two halves of the housing and secure with screws.

Springs are used within outdoor power equipment to provide tension and shock absorption, depending on their application and use. This spring is designed for use within trimmers/brush cutters and is made to provide tension on the spool reel mechanism, and in some cases may be used to advance the line whenever portions of it are cut off. Th...Read moreis spring measures approximately 1.3-inches in length when extended and comes as an individual part. If you notice the line/spool in your trimmer is not advancing or is coming too quickly, the spring may be damaged and need replacing. Since this spring is a high-use part, it is not uncommon for it to lose tension over time and need to be replaced. To replace the spring, you will need to unscrew the covering cap, remove the spool feeding reel, remove the old spring and install the new spring with the rest of the assembly. Make sure to feed the line back into the appropriate feeding holes prior to operation of the trimmer.

This fuel filter is a genuine OEM part that is compatible with various lawn equipment models and is sold as an individual part. Fuel filters are used to remove dirt and debris from fuel entering the carburetor and engine and are made of metal with a fabric filter material, meaning this filter will eventually clog and need to be replaced. ...Read morePlease note that the fuel filter should be inspected regularly, not solely when it is clogged. The filter will be attached to the fuel line within the fuel tank and if your equipment is having starting, revving, or idling issues, the fuel filter may be the reason why. To replace it, simply use a hook to pull the old filter out from the fuel tank, use pliers to remove any clamps attached to the end of the fuel line, and pull the filter off. Attach the new filter to the fuel line, along with the clamp, and set the filter back into the tank.

Effortlessly improve the performance of your Ryobi units with the Throttle Cable and Wire Assembly. Designed with precision and quality in mind, this authentic part ensures lasting durability and peak performance in a variety of Ryobi models. The Throttle Cable and Wire Assembly optimizes the control and response of your equipment, making...Read more each task more efficient. Experience the superior performance and reliability that this integral component brings. Genuine and dependable, it truly embodies Ryobi's commitment to innovation and excellence in one package.