RY13050A Ryobi Edger - Overview

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This is a genuine Ruixing replacement part, it is sold individually. By pressing the bulb, it will purge the carburetor of air. Fuel will be forced up from the fuel tank through the fuel line then into the carburetor. Then the excess fuel will be forced back into the fuel tank through the fuel return line. At some time the primer will l...Read moreose its elasticity or crack and need to be replaced. We have an article and video on How to Replace a Primer Bulb, in our Repair Center. That can be found on the front page of our site.

This is a genuine OEM replacement part, it is made out of Metal with Fabric Filter Material. It is sold individually and is used on a variety of Lawn and Garden Equipment. This is an in-tank fuel filter which makes sure that the fuel delivered to the engine is free of any debris or contaminants. It will over time become clogged and restrict the fuel getting to the engine so it will need to be replaced.

This replacement gasket is an authentic OEM item that is specially designed for Ryobi lawn and garden equipment. This gasket provides an air-tight seal for the oil pan. Over time gaskets tend to shrink, become brittle and crack eventually requiring a replacement. It is made from high quality composite material and it is sold individually.

This is an OEM sourced replacement part used on gas trimmers. A centrifugal clutch is a part that uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driven shaft. Today's centrifugal clutches will function even when they shouldn't, far beyond the point of when they need to be replaced. Keepin...Read moreg an eye on equipment performance will determine when the centrifugal clutch requires attention. Please note the clutch drum, spacer and washer are all sold separately. This clutch is made out of metal and it is sold individually. To replace this item you would need a screwdriver and pliers.

This is an authentic OEM sourced replacement screw. It is specially manufactured for use with a variety of handheld lawn and garden equipment. This is a standard hardware which has multiple applications based on your unit. Please refer to appropriate diagrams for correct location and application of this screw. This screw is made out of me...Read moretal and it is sold individually. To remove or install it you will need a torx screwdriver.

This is an original Ryobi replacement part manufactured for use with lawn and garden equipment. The plastic starter grip sits at the end of the starter rope and is pulled to start the engine. This starter grip is available individually, please see model diagram for associative parts.

(M4 x 12 mm)

This genuine replacement carburetor is sourced from original manufacturer and it is designed for use with gas trimmers. It mixes air and gas before the fuel mix goes to the engine. If the engine won't start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the ca...Read morerburetor. Pull the starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem. This assembly includes a metal body carburetor with a plastic choke lever. When replacing carburetor it is advised that you also replace carburetor gaskets to ensure proper air tight seal for optimum performance. You will need a screwdriver to perform this repair.

This replacement screw is a high quality hardware that is supplied by original equipment manufacturer for use with Homelite and Ryobi handheld lawn and garden equipment. This screw is a standard hardware which will have multiple applications depending on your unit, please make sure to check appropriate diagrams for correct location and use of this item. One durable metal torx screw is included per order.

This is an OEM part which is specially made for Ryobi handheld lawn and garden equipment. The check valve connects between the breather hose allowing air into the engine. Over time it may wear out or get damaged eventually requiring a replacement. One durable plastic check valve is included. You may need a screwdriver to perform this repa...Read moreir. Check the appropriate diagrams for your specific model to ensure the exact location and the correct application.

This is a genuine replacement part sourced from the original manufacturer for use with edgers, sanders, and miter saws. The special ball bearing is commonly used to reduce friction between a rotating shaft and fixed part assembly. This ball bearing is available as an individual replacement please see model diagram for associative parts.