RY13015 Ryobi Trimmer - Overview

This OEM sourced replacement fuel tank assembly is designed for use with Ryobi string trimmers. It is made out of plastic and it includes the fuel tank, fuel lines, fuel cap and the fuel filter. Please note the screws used to secure it are sold separately. It is very important to replace the fuel tank if it is cracked or damaged to avoid ...Read moredamage or serious injuries. Make sure to drain the gas tank before starting a repair.

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This is a genuine Ruixing replacement part, it is sold individually. By pressing the bulb, it will purge the carburetor of air. Fuel will be forced up from the fuel tank through the fuel line then into the carburetor. Then the excess fuel will be forced back into the fuel tank through the fuel return line. At some time the primer will l...Read moreose its elasticity or crack and need to be replaced. We have an article and video on How to Replace a Primer Bulb, in our Repair Center. That can be found on the front page of our site.

This flanged star washer is a manufacturer-sourced replacement part designed for use trimmers. It is also known as a tooth lock washer due to its serrated inner edge which resembles inward facing teeth. These teeth bite into the head of the fastener and provide a better grip than standard washers. This washer also has a flange on one side...Read more which is a lip that extends past the edge of the washer. It helps to distribute the load of the fastener over a wider area to provide extra stability and a more secure hold. Over time the washer may wear down or become damaged. To remove the washer, first unthread the bolt/screw it is fastened on. Use pliers to grip the washer and gently twist it off. Place the new washer over the fastener with the teeth facing toward the surface being fastened and insert it into the designated hole. Ensure that it is locked into place. Each washer is sold individually.

Genuine OEM replacement part, this part is sold individually. This part is where the stringhead assembly is mounted on the Trimmers shown below. It attaches to the spindle. The thread mount on the spindle is a left hand thread.

This Gear gear head assembly is designed to transfer power from the drive shaft to the cutting head, allowing the string trimmer or brush cutter to operate smoothly and efficiently. Housed in a durable gearcase, it supports reliable rotation and helps maintain consistent cutting performance during use. Replacing a worn or damaged gear hea...Read mored can resolve issues such as loss of power to the cutting head, excessive noise, or erratic operation, restoring dependable performance. A properly functioning gear head also helps reduce strain on the drive system, contributing to longer service life and more efficient trimming results.

This replacement gasket is an authentic OEM item that is specially designed for Ryobi lawn and garden equipment. This gasket provides an air-tight seal for the oil pan. Over time gaskets tend to shrink, become brittle and crack eventually requiring a replacement. It is made from high quality composite material and it is sold individually.

This is an OEM sourced replacement part used on gas trimmers. A centrifugal clutch is a part that uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driven shaft. Today's centrifugal clutches will function even when they shouldn't, far beyond the point of when they need to be replaced. Keepin...Read moreg an eye on equipment performance will determine when the centrifugal clutch requires attention. Please note the clutch drum, spacer and washer are all sold separately. This clutch is made out of metal and it is sold individually. To replace this item you would need a screwdriver and pliers.

This is the OEM part from Ryobi. The starter pulley is constructed of durable plastic, and has been designed for use with a variety of lawn and garden devices. This item is often part of the starter assembly, and is fastened between the spring & container and air dam. Please consult specific manual and diagrams for repair instructions. Th...Read moreis part is sold individually. A hex key is usually needed in making the replacement.

This is a genuine item that is supplied by the original equipment manufacturer for Ryobi, Toro and Homelite handheld lawn and garden equipment. It is an identical replacement for a missing or damaged string guard clamp that was originally installed on a new unit, please make sure to refer to the owners manual of your model for the correct...Read more application of this component. Keep in mind this high-quality part is made of durable metal and is sold individually.

This replacement bolt is sourced from original equipment manufacturer for use with Ryobi string trimmers. It is generally used to secure the spool to the trimmer shaft. This is a hex head bolt which is sold individually. Note, when installing or removing this bolt you would need a wrench.

This genuine part is supplied by the original equipment manufacturer for use with Ryobi handheld lawn and garden equipment. The cap is designed to keep the fuel in the tank. Note that it is a vented cap that lets the air back into the tank so a vacuum is not created. It provides an identical replacement for a missing or a faulty component...Read more that was included with a new unit. Please make sure to check the diagrams of your model for the correct location and installation. Keep in mind this high-quality fuel cap assembly is made of durable plastic and is sold individually.