RY13010 Ryobi Trimmer - Overview

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This is a genuine Ruixing replacement part, it is sold individually. By pressing the bulb, it will purge the carburetor of air. Fuel will be forced up from the fuel tank through the fuel line then into the carburetor. Then the excess fuel will be forced back into the fuel tank through the fuel return line. At some time the primer will l...Read moreose its elasticity or crack and need to be replaced. We have an article and video on How to Replace a Primer Bulb, in our Repair Center. That can be found on the front page of our site.

This flanged star washer is a manufacturer-sourced replacement part designed for use trimmers. It is also known as a tooth lock washer due to its serrated inner edge which resembles inward facing teeth. These teeth bite into the head of the fastener and provide a better grip than standard washers. This washer also has a flange on one side...Read more which is a lip that extends past the edge of the washer. It helps to distribute the load of the fastener over a wider area to provide extra stability and a more secure hold. Over time the washer may wear down or become damaged. To remove the washer, first unthread the bolt/screw it is fastened on. Use pliers to grip the washer and gently twist it off. Place the new washer over the fastener with the teeth facing toward the surface being fastened and insert it into the designated hole. Ensure that it is locked into place. Each washer is sold individually.

Genuine OEM replacement part, this part is sold individually. This part is where the stringhead assembly is mounted on the Trimmers shown below. It attaches to the spindle. The thread mount on the spindle is a left hand thread.

This Gear gear head assembly is designed to transfer power from the drive shaft to the cutting head, allowing the string trimmer or brush cutter to operate smoothly and efficiently. Housed in a durable gearcase, it supports reliable rotation and helps maintain consistent cutting performance during use. Replacing a worn or damaged gear hea...Read mored can resolve issues such as loss of power to the cutting head, excessive noise, or erratic operation, restoring dependable performance. A properly functioning gear head also helps reduce strain on the drive system, contributing to longer service life and more efficient trimming results.

This replacement gasket is an authentic OEM item that is specially designed for Ryobi lawn and garden equipment. This gasket provides an air-tight seal for the oil pan. Over time gaskets tend to shrink, become brittle and crack eventually requiring a replacement. It is made from high quality composite material and it is sold individually.

This is an OEM sourced replacement part used on gas trimmers. A centrifugal clutch is a part that uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driven shaft. Today's centrifugal clutches will function even when they shouldn't, far beyond the point of when they need to be replaced. Keepin...Read moreg an eye on equipment performance will determine when the centrifugal clutch requires attention. Please note the clutch drum, spacer and washer are all sold separately. This clutch is made out of metal and it is sold individually. To replace this item you would need a screwdriver and pliers.

This is a genuine item that is supplied by the original equipment manufacturer for Ryobi, Toro and Homelite handheld lawn and garden equipment. It is an identical replacement for a missing or damaged string guard clamp that was originally installed on a new unit, please make sure to refer to the owners manual of your model for the correct...Read more application of this component. Keep in mind this high-quality part is made of durable metal and is sold individually.

This replacement bolt is sourced from original equipment manufacturer for use with Ryobi string trimmers. It is generally used to secure the spool to the trimmer shaft. This is a hex head bolt which is sold individually. Note, when installing or removing this bolt you would need a wrench.

This replacement wing screw is a genuine OEM sourced item, it is not an aftermarket imitation. It is specially designed for Homelite and Ryobi string trimmers and brush cutters. This hardware is generally used to secure the grass deflector. This screw is made from durable metal and it is sold individually.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Homelite and Ryobi handheld lawn and garden equipment. This is the special screw which is utilized to secure the gear head, please refer to the appropriate diagrams of your model for the correct location and application of this hardware. K...Read moreeep in mind this durable metal hex head screw is sold individually, you will need a wrench to secure or remove it.

This is an authentic OEM sourced replacement screw. It is specially manufactured for use with a variety of handheld lawn and garden equipment. This is a standard hardware which has multiple applications based on your unit. Please refer to appropriate diagrams for correct location and application of this screw. This screw is made out of me...Read moretal and it is sold individually. To remove or install it you will need a torx screwdriver.