RY09951 Ryobi Leaf Blower / Vacuum - Overview

This authentic OEM starter rope measures 42-inches and is for use with various models of outdoor power equipment. Made of nylon, this rope wraps around the starter recoil spring and when pulled, is used to start the engine. This rope is sold as an individual part, so any necessary grips are sold separately.

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This is a genuine Ruixing replacement part, it is sold individually. By pressing the bulb, it will purge the carburetor of air. Fuel will be forced up from the fuel tank through the fuel line then into the carburetor. Then the excess fuel will be forced back into the fuel tank through the fuel return line. At some time the primer will l...Read moreose its elasticity or crack and need to be replaced. We have an article and video on How to Replace a Primer Bulb, in our Repair Center. That can be found on the front page of our site.

This is a genuine Homelite replacement part, it is sold individually. The Leaf bag is used on the models listed below. It is attached to the main hosing of the blower. When using the leaf bag, you will want to use the tubes of your choosing that are on the part diagram, for the job you are doing

This OEM high-velocity nozzle directs and concentrates the airflow from your leaf blower to specific areas. It easily twists into the upper blower tube and features a wet leaf scraper blade for clearing wet debris. Signs of a broken nozzle include visible cracks, instability, or poor airflow. Failure to replace a damaged nozzle will resul...Read moret in inefficient debris clearing. Your leaf blower may disperse airflow in unintended directions. To remove the nozzle, gently twist it counterclockwise and then pull it straight out. This tube nozzle is sold individually.

This is an authentic OEM sourced replacement momentary contact switch. It is specially designed for Homelite and Ryobi blowers and vacuums. It is the part of the tool handling on and off function of the tool. Please note, these mechanical switches have will over time wear out requiring replacement. This switch has a plastic body and it is sold individually. To replace this item no tools would be needed.

This manufacturer approved replacement starter pulley is designed for use with gas blowers/vacuums. This recoil pulley is susceptible to a normal wear due to constant wear and will eventually require replacement. It is made out of plastic and it is sold individually. Please note, housing, rope and starter grip are all sold separately. To complete this repair you will need a screwdriver and an allen wrench/hex key.

Genuine OEM replacement part, this item is sold individually. This part is used on the carburetors on the outdoor power equipment listed below. Because this part is used quite frequently it has a tendency to wear. To replace it, simply press it on the Choke Shaft of the carburetor.

Genuine Manufacturer Sourced replacement part used on Blowers/Vacuums and String Trimmers. This part is made out of Composite Material and it is Sold Individually. This Gasket provides an Air Tight Seal between the Heat Dam and Carburetor which acts as a spacer allowing it to stay cool.

Genuine Manufacturer Sourced replacement part used on certain Hedge Trimmers and Blowers. This part is made out of Plastic and it is Sold Individually. Heat Dam acts as a spacer for carburetor allowing it to stay cool.

This fuel tank assembly is an OEM replacement part supplied by the manufacturer. It is commonly used in Ryobi and Homelite blower/vacuums. This fuel tank assembly contains the gasoline needed to operate these machines. This assembly should be replaced if any of the included parts are missing or damaged. A screwdriver is required to comple...Read morete this replacement. -Remove the three mounting screws -Disconnect the two fuel lines -Remove old tank and replace with the new -Connect the two fuel lines -Reattach the three mounting screws