RTW4100WQ1 Roper Washer Parts & Repair Help | PartSelect
Models > RTW4100WQ1

Manuals & Care Guides for RTW4100WQ1

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(139)
PartSelect #:PS1485646
Manufacturer #:285753A
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission ...
$23.15
In Stock
(25)
PartSelect #:PS11743345
Manufacturer #:WP63907
The suspension spring supports the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down or has stretched out and lost it...
$4.80
In Stock
(59)
PartSelect #:PS334641
Manufacturer #:285785
A clutch assembly (Clutch, Washer Clutch) is found in your washing machine and is responsible for spinning the basket during the spin cycle. The clutch lining can wear over time. I...
$49.12
In Stock
(9)
PartSelect #:PS11741866
Manufacturer #:WP358237
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
$7.48
In Stock
(59)
PartSelect #:PS11745957
Manufacturer #:WP8318084
This part is found in your washer. The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the green grounding wire....
$39.01
In Stock
(2)
PartSelect #:PS11746840
Manufacturer #:WP90767
This screw is sold individually.
$7.76
In Stock
(6)
PartSelect #:PS334620
Manufacturer #:285744
This package of pads contains three brown tub wear pads.
$16.92
In Stock
(1)
PartSelect #:PS11747965
Manufacturer #:WPW10001130
The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a ru...
$7.48
In Stock
(5)
PartSelect #:PS394983
Manufacturer #:8316845
This spring is used on the leveling components in a washer. Please note, this spring may differ in appearance, but functions the same as original.
$8.60
In Stock
(6)
PartSelect #:PS11723081
Manufacturer #:W10814296
This part may also be referred to as a main outer tub seal. This part prevents leaking from the bottom of the tub. The gasket is approximately 2 inches in diameter to the outer edg...
$5.80
In Stock
Questions and Answers for RTW4100WQ1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No movement from Basket & agitator

  • Customer: Jeff from Wayne, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1014 of 1075 people found this instruction helpful
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor co... read more

spin cycle did not engage

Clutch Assembly – Part Number: 285785
  • Customer: Andrew from SLC, UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 463 of 491 people found this instruction helpful
researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unbolted the 3 gearcase... read more

Washer wouldn't run

Washer Lid Switch – Part Number: WP8318084
  • Customer: Clint from Kansas City, KS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 294 of 327 people found this instruction helpful
I removed the two screws on the back of the control panel. The control panel then flips back. The switch is on the left side. To remove the switch, I first detached the wire to the control panel and unscrewed the grounding wire. The new switch drops right in. I had a little trouble getting it in until I realized the washer lid had to be open. A little ... read more