This evaporator fan blade moves cooled air through the refrigerator or freezer compartments when driven by the fan motor. A cracked, warped, or loose blade may vibrate, strike nearby parts, or fail to move enough air. Unusual ticking or humming noises and warmer compartment temperatures may be reasons to inspect the fan assembly. Check fo...Read morer ice buildup and motor or mounting problems as well, since these can cause similar symptoms. Disconnect power before accessing the blade and follow the appliance instructions for fitting it securely on the motor shaft. This is an OEM part sourced directly from the manufacturer.
This water valve kit, also known as a single outlet water valve kit, is used in refrigerators. The kit includes a union, two screws, and some tubing pieces. If one of the solenoids in your water valve is not allowing water to flow into the icemaker or the dispenser, it might be damaged or broken. If this is the case, it is best to replace...Read more this part. To repair, first remove the cardboard panel at the rear of the fridge. Next, remove the tubing that supplies water to the valve with a 1/2 inch wrench. Once it is accessed, refer to the manual guide provided by the manufacturer for further installation instructions and guidance.
This is a door/light switch and it is a replacement part for your refrigerator. This part is activated as you open and close your refrigerator door. When the switch is activated and the door is open it will turn the light on inside your appliance, and when you close the door the switch will deactivate the light. Before purchasing this par...Read moret, you may test it for continuity to determine if your current switch is defective and needs replacing. This model is white in color and measures to be roughly one inch thick, almost two inches high, and almost 1.5 inches deep, with a male end plug.
This ice container is white in color and made of plastic. This part lays flat inside the freezer compartment. The container is approximately 13 inches front to back, 10 inches side-to-side, and 5 inches deep, weighing 2 lbs. The ice container holds the ice in the freezer section for dispensing. Due to the frigid temperatures of your freez...Read moreer, plastic can break and crack over time and will need to be replaced. This is an OEM part that is sourced right from the manufacturer, ensuring the best possible quality.
This refrigerator defrost timer will cycle for twenty-one minutes after every six hours of run time. Use it for your Frigidaire/WCI brand refrigerator.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Icemaker Wasnt Making Ice
12 of 16 peoplefound this instruction helpful.
ERIC from SAN ANTONIO, TX
Really Easy
15 - 30 mins
Nutdriver, Pliers
After unplugging electric cord and turning off water at wall, I then removed the two screws that secured the valve to the refrigerator. I then removed the water connections to the valve and removed a short portion of the hose going to the icemaker. I then installed the connection pieces provided package and reversed the procedures to
... Read more install the new part. It was easier than I thought it would be.
Read less
Was this helpful?
Thank you for voting!
Erratic light.
9 of 11 peoplefound this instruction helpful.
D KIRKE from CORVALLIS, OR
Really Easy
Less than 15 mins
Simple switch repair: Unplug fridge, pull down to remove switch assembly, slip contacts off. Reverse with replacement switch. HOWEVER, check first to see if the bulb filament might be broken, as this could cause the same symptom. OR in my case, the light socket connection was the culprit. Check that too before ordering a replacement s
... Read morewitch.
Read less
Was this helpful?
Thank you for voting!
ice maker did not work.
6 of 7 peoplefound this instruction helpful.
LARRY from HANOVER, MD
Easy
15 - 30 mins
Nutdriver
I pulled the cover from back of fridge then removed two screws from the water valve disconected the wires and removed water lines. had to reroute water lines so the universal part would fit. don't forget to turn off the water befor doing the above. found new mounting hole and reconected water lines. worked like a champ.