RS744GP1 Hotpoint Range - Overview
Sections of the RS744GP1
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Large Surface Burner Switch - 2350W 240V
PartSelect #: PS236303
Manufacturer #: WB23K5027
This infinite heat control switch is a genuine OEM component designed for electric ranges with 8-inch surface burners. Engineered to regulate power flow to the heating element, it enables precise temp...
$109.43
In Stock
Switch
PartSelect #: PS1765837
Manufacturer #: WB24T10147
This light switch is controlled by opening and closing the oven door
$30.53
In Stock
Door Lock and Switch Assembly
PartSelect #: PS2577623
Manufacturer #: WB49T10020
Enhance the functionality of your GE range with this Oven Door Lock Assembly. Primarily designed to provide additional safety, this component locks the oven door during the self-cleaning cycle, helpin...
$158.94
In Stock
Common Symptoms of the RS744GP1
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Convection oven fan and door light not working
The first step was to determine whether the problem was with the fan itself or the switch. I did this by opening the back cover and using a Volt meter to verify that the fan was not getting power. (I could have skipped this step.)
Next, I unplugged the range, closed up the back cover and lifted the range hood by removing two he ... Read more x head screws that are just inside and on either side of the top of the opening in the range door. Propping the hood open, I removed the connector leading to the switch, then pushed the switch out the front. Inspection showed that the switch was damaged so I closed up the range and ordered the part from Part Select. Once the part arrived, it was a 15 minute job to unplug the range, lift the top, install the new switch, and close up the unit.
Caution. On starting to install the switch, I failed to unplug the range and my finger brushed one of the hot contacts leading to the switch. Thankfully, I was not injured. Do not repeat my mistake on this issue. Unplug the range even if you're only installing this simple switch.
Next, I unplugged the range, closed up the back cover and lifted the range hood by removing two he ... Read more x head screws that are just inside and on either side of the top of the opening in the range door. Propping the hood open, I removed the connector leading to the switch, then pushed the switch out the front. Inspection showed that the switch was damaged so I closed up the range and ordered the part from Part Select. Once the part arrived, it was a 15 minute job to unplug the range, lift the top, install the new switch, and close up the unit.
Caution. On starting to install the switch, I failed to unplug the range and my finger brushed one of the hot contacts leading to the switch. Thankfully, I was not injured. Do not repeat my mistake on this issue. Unplug the range even if you're only installing this simple switch.
Read less
Parts Used:
-
Michael from Albuquerque, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
18 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
uncontrollable heat - would not cycle off
Turn circuit breaker off.Raise up cook top and remove 6 screws that hold catch pan in place.move 3 screws that hold switch cover panel [2 sections]in place. Pull off knob for bad switch and remove 2 screws.Pull off each of the 5 wire terminal clips by removing one at a time and replacing that one on the new switch control to assure correc
... Read more
t placement.Reinstall switch cover panel and catch pan.
Read less
Parts Used:
-
anthony from maumelle, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
17 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace oven door handle
I first removed oven glass panel from frame by removing three screws which secured it to the frame. I then removed the spacer and handle mounts with a 1/4 inch nut driver. This is the only tool that worked for the application. Using an oen wrench or a rachet without a long extension would have taken much more time. Then reattached new
... Read more
handle using existing screws and resecured oven dorr glass to the frame.
One thing to look at is the old handle bracket vs. new bracket. The old bracket had metal threaded inserts to secure the mounting screws. The new handle is all plastic. This said, the existing screws might not work for the application and may split the plastic mounting bracket if it is over tightened. In my case they worked fine but, it is just something to think about.
One thing to look at is the old handle bracket vs. new bracket. The old bracket had metal threaded inserts to secure the mounting screws. The new handle is all plastic. This said, the existing screws might not work for the application and may split the plastic mounting bracket if it is over tightened. In my case they worked fine but, it is just something to think about.
Read less
Parts Used:
-
Daniel from Centreville, VA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
12 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!