This microwave fuse is just over an inch in length. It has a white ceramic center, and metal on either end. This is a twenty amp 250-volt fuse, and is used to power your microwave. If your microwave will not heat properly, will not turn on, or the touch pad becomes unresponsive, there could be a faulty fuse which should be replaced. Remem...Read moreber, since this part contains an electrical charge, before you replace the fuse from your microwave, make sure that the power is disconnected from the unit. This part is sold individually.
NOTE: Make sure your microwave is unplugged, and your capacitor is discharged before you begin this repair. A capacitor stores large amounts of electricity even after your microwave is unplugged.
This oven light assembly is a little over four inches long and comes with the lens and 660-watt light bulb. Make sure your appliance is unplugged or circuit breaker is off before installing this new part. It is located inside the oven and may need to be replaced if the socket has failed, causing the light to not come on inside the oven. I...Read moret may also need to be replaced if you notice that the glass is broken and the whole assembly needs to be replaced. The part is located in the upper right hand side of the oven. To reach the bulb you will need to open the oven door and remove the upper rack.
The hinge kit, or oven door hinge, is used in ranges and wall ovens. The hinge attaches to the right side of the door and controls how fast the door opens. At a specific angle, it allows the door to remain open. If you are having trouble opening and closing your door, or it does not close at all, replacing the hinge could solve your probl...Read moreem. The hinge is made from metal and the kit comes with the hardware needed for this installation. You will need a screwdriver to perform this repair. *Please note: This part is only for the right side of your appliance. The left side is sold separately.
This gas burner grate is used for some gas ranges and cooktops. This is a black burner grate with each side measuring almost eight inches. This part may become rusted or burnt over time if not properly taken care of or with excessive use. If you notice that your grate is discolored or blackening, it may need to be replaced. The surface bu...Read morerner grate provides a steady surface for your cookware that is placed on top of the surface burner. This is a genuine OEM part that is sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Blows main fuse when the microwave generator start, (cooking function).
39 of 48 peoplefound this instruction helpful.
Jay from Edwardsville, IL
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers
Remove microwave from oven cabinet. remove cover and check main fuse with ohm meter. Tried fuse, it does not blow untill cooking starts. Check capacitor with ohm meter, after properly performing capacitor dischagre procedure. Order new capacitor, simple installation. another new fuse and all is good and cooking again.
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With th
... Read moree help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix .
Read less
Was this helpful?
Thank you for voting!
There was a crack in the porcelain not letting it spark
23 of 36 peoplefound this instruction helpful.
Billy from Martinsville, IN
Really Easy
Less than 15 mins
Screw drivers
I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire. Then just connected the new electrode and place the assy, in the burner.