RGV12K36030 Subaru Generator - Overview

An oil drain plug is a part designed to facilitate a convenient and controlled method for draining the oil from an engine and is commonly positioned at the lower part of the machine, threaded into the oil sump or pan, offering an easier point for oil removal. This plug is designed for use within various types of small engine equipment and...Read more requires a hex socket wrench to remove and install. This plug is an OEM part that is sold as an individual and prevents any oil from leaking from the oil sump/pan and need only be removed for oil changes. If you notice an oil leak or poorer performance from your equipment, it may be due to an oil leak caused by a broken or loose plug. To replace this plug, ensure you use the torque setting set by the manufacturer of your equipment to properly secure it.

This is a genuine OEM supplied component which is specially made for use with Subaru / Robin engines commonly installed on lawn and garden equipment. It is a standard hardware which may have multiple applications depending on the model of your unit, please make sure to refer to the appropriate diagrams for the correct location and applica...Read moretion of this part. Keep in mind this high-quality flange bolt is made of durable metal and is sold individually.

This OEM flange nut in your engine is a fastener that secures different engine assemblies, like the intake system or the fuel tank. It has a wide, flat base for stability and even load distribution. With a diameter of 6 mm, a thread pitch of 1 mm, and a flange diameter of 13 mm, it is commonly found at assembly attachment points or in are...Read moreas that vibrate. You can tell if a flange nut is broken by checking for bending, cracking, or missing pieces. You may also notice loose assemblies. Not replacing a broken flange nut can lead to issues such as air or fuel leaks and a loss of engine power. To remove a damaged nut, consult your user manual for its location and use a wrench or socket to unthread it. Please note that this flange nut is sold individually, so it is essential to confirm the quantity required for your specific machine. It is also a good idea to keep some extras on hand for future repair needs.

This gasket, also known as the oil drain plug gasket, is a ring-shaped, metal component used in outdoor power engines. It is supplied by the manufacturer and can be found at the bottom of the engine oil pan where the drain plug is installed. The gasket is responsible for sealing the area between the oil drain plug and the engine block to ...Read moreprevent oil from leaking during oil changes. Over time the gasket can wear down, corrode, or crack. If the gasket can no longer seal the area, oil will escape from the oil pan, leading to inadequate lubrication, increased friction, and engine damage. Before you begin the repair, drain the oil from the engine to prevent contamination. Use a wrench to loosen and remove the oil drain plug. Peel off the old gasket, and thoroughly clean the drain plug and oil pan surface. Install the new gasket and ensure that it sits firmly on the oil pan. Finally, reinstall the drain plug, and be careful to avoid overtightening it.

This intake valve seal is an OEM part that creates a tight seal between the intake valve and the cylinder head, preventing air-fuel mixture leakage. A broken seal may show signs of being distorted, cracked, or torn, and you may notice leakage around the valve. If the broken seal is not replaced, it can harm engine performance and efficien...Read morecy. To remove the seal, disconnect components like the intake and exhaust manifolds, and unbolt the cylinder head from the engine block. Locate the seal and use a socket wrench to remove the fasteners securing the valve spring retainer. Compress the valve spring with a valve spring compressor and remove the valve keepers. Release the compressor and take off the retainer and spring. Gently tap the seal intake valve with a rubber mallet to loosen and remove it. Please bear in mind that this seal is sold individually and the valve is sold separately.

This cleaner element is a high quality item designed for use on Subaru/Robin engines. It is sourced from original equipment manufacturer and it is sold individually. This combo includes (1) pleated paper filter and (1) foam pre-filter element. The purpose of these filters is to remove dust and other contaminants from the air that goes into the carburetor. To replace this part no tools would be needed.

This is an authentic Subaru/Robin replacement part. The wing nut is commonly found in small engines. This part is composed of a high-quality plastic knob with a threaded metal insert. It is used to hold the air cleaner assembly in place. No tools are required when replacing this item. Simply unscrew the old part and thread the new one into place. This item is sold individually.

This oil filter assembly is an authentic OEM replacement part that is designed for use with Subaru / Robin engines. This part is used to remove harmful contaminants from engine oil. This part maintains optimum performance of your engine in accordance with applicable EPA emissions regulations, it is advised to replace it at least once a season. Please note this oil filter is sold individually.